NACE NACE-CIP2-001問題集で必ず試験合格させる
NACE-CIP2-001試験問題（更新されたのは2024年）100%リアル問題解答
NACE-CIP2-001試験の受験資格には、コーティング検査における最低2年の経験とNACE-CIP1試験の合格が必要です。試験は、4時間以内に100の多肢選択問題を解答する必要があります。試験はコンピュータベースで、結果は完了後すぐに利用可能です。
質問 # 35
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Use a generally accepted industry standard and to take readings
- B. Develop your own methodology and proceed take the readings
- C. Refuse to take readings until an is in place
- D. Call your supervisor
正解：A
質問 # 36
Ideally, documentation requirements should be defined:
- A. By the contractor
- B. By the inspector
- C. In the specification
- D. At the pre-job conference
正解：C
質問 # 37
Inspection and Test plans are developed by referencing:
- A. The Specification, Application Guidelines, 'Relevant Standards and Codes
- B. The Specification, Safety Manual, Relevant Standards and Codes
- C. The Specification, TDS, relevant Standards and Codes
- D. The Specification, SDS, relevant Standards and Codes
正解：C
質問 # 38
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Suggest to the Owner that the supervisor should be removed from site
- B. Challenge the supervisor's authority
- C. Express a willingness to work with the site team and follow the specification
- D. Defend the previous inspector
正解：C
質問 # 39
In which type of concrete are laitance commonly encountered?
- A. Glass fiber cement
- B. Poured (wet cast)
- C. Concrete block (poured with a form)
- D. Gunite
正解：B
質問 # 40
NACE Level 2 Inspectors have been authorized to perform:
- A. Visual inspection and Non-destructive testing
- B. Visual inspection, Non-Destructive and Destructive testing
- C. All types of inspection without supervision
- D. Visual inspection only
正解：B
質問 # 41
A single component water borne acrylic coating cures by:
- A. Oxidation
- B. Coalescence
- C. Co-Reaction
- D. Solvent Evaporation
正解：B
質問 # 42
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Slightly different to air blast cleaning
- B. Comparable to air blast cleaning
- C. Different than air blast cleaning
- D. The same as air blast cleaning
正解：D
質問 # 43
When ASIN D 3363 is specified the Inspector must:
- A. Record the percentage of failure
- B. Record the highest value attained
- C. Use the correct solvent
- D. Record the two end points identified in the standard
正解：D
質問 # 44
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Review the standard with the Contractor and re-inspect the floor
- B. Shut the job down
- C. Request that the Contractor re-blast the floor
- D. Call your supervisor
正解：A
質問 # 45
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Supervision Costs
- B. Lower Application Costs
- C. Lower Safety Enforcement Costs
- D. Lower Coating Life Cycle Costs
正解：D
質問 # 46
NACE No.13/ SSPC 6 identifies the use of:
- A. Abrasive blasting only
- B. Various methods of cleaning
- C. Watterjetting only
- D. Steam cleaning only
正解：B
質問 # 47
In the event of a conflict between the Product Data Sheet and the Specification:
- A. The Product Data Sheet prevails
- B. It is up to the Applicator to decide which one to follow
- C. The Specification prevails
- D. It is up to the Inspector to decide which one to follow
正解：C
質問 # 48
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only technical experts would understand
- B. Language that only in the project would understand
- C. Language that the most would understand
- D. Language that another NACE Inspector would understand
正解：C
質問 # 49
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Organic coatings
- B. Latex
- C. Polyurea
- D. Inorganic Coatings
正解：D
質問 # 50
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of acid or caustic splashes
- B. Risk of skin
- C. a), b), and c)
- D. Risk of chemical exposure
正解：C
質問 # 51
......
NACE-CIP2-001試験を受験するには、候補者はNACE承認のコーティングインスペクターレベル1トレーニングコースを修了し、コーティング検査分野で少なくとも2年の経験を持っている必要があります。レベル2認定は、NACEコーティングインスペクタープログラムの2番目の認定レベルであり、レベル1コースで習得した知識とスキルをさらに発展させるものです。
合格させるNACE NACE-CIP2-001試験最速合格にはFast2test：https://jp.fast2test.com/NACE-CIP2-001-premium-file.html
準備NACE-CIP2-001問題解答でNACE-CIP2-001試験問題集：https://drive.google.com/open?id=1qCJk8w32W1D8YJbUVoD39Fx4bzfmmVti