更新された2024年01月合格させるNACE-CIP2-001試験リアル練習テスト問題
無料ダウンロードNACE NACE-CIP2-001リアル試験問題
質問 # 16
NACE No.13/ SSPC 6 identifies the use of:
- A. Watterjetting only
- B. Abrasive blasting only
- C. Various methods of cleaning
- D. Steam cleaning only
正解：C
質問 # 17
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Call your supervisor
- B. Enforce the additional requirement
- C. Request clarification from the specifier
- D. Ignore the additional requirement
正解：B
質問 # 18
Inspection and Test plans are developed by referencing:
- A. The Specification, TDS, relevant Standards and Codes
- B. The Specification, SDS, relevant Standards and Codes
- C. The Specification, Application Guidelines, 'Relevant Standards and Codes
- D. The Specification, Safety Manual, Relevant Standards and Codes
正解：A
質問 # 19
The main reason dehumidification is used during coating operations is to
- A. control the environment
- B. avoid repetitive blasting/coating operations.
- C. allow the contractor to guarantee the completion date.
- D. reduce the possibility of missing the recoat window.
正解：A
質問 # 20
Galvanizing performs best in which of the following exposures:
- A. pH of 13
- B. pH between 5-10
- C. pH above 12
- D. pH below 4
正解：B
質問 # 21
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Review the NACE Attestation prior to making a decision
- B. Accept assignment without hesitation
- C. Advise the prospective employer that you cannot accept the position
- D. Meet with the prospective employer to scope of your role
正解：A
質問 # 22
When ASIN D 3363 is specified the Inspector must:
- A. Use the correct solvent
- B. Record the highest value attained
- C. Record the percentage of failure
- D. Record the two end points identified in the standard
正解：D
質問 # 23
The best choice of instrument for holiday testing of thick film concrete coatings is:
- A. Low Voltage Sponge Type
- B. High Voltage AC
- C. High Voltage DC Pulse Type
- D. High Voltage DC Constant Current
正解：D
質問 # 24
The Concrete Repair Institute's comparators can be used to assess:
- A. Surface profile prior to coating
- B. Contamination levels prior to coating
- C. Compressive and tensile strength prior to coating
- D. Surface cleanliness prior to coating
正解：A
質問 # 25
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. False
- B. True
正解：A
質問 # 26
Dehumidification is defined as the removal of moisture vapor from the air to
- A. provide worker comfort.
- B. raise its relative humidity.
- C. lower its temperature
- D. lower its dew point,
正解：D
質問 # 27
External coatings applied to buried pipelines are generally tested for:
- A. Solvent resistance
- B. Gloss level
- C. Cathodic disbondment
- D. Chalking resistance
正解：C
質問 # 28
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method A - Cross Hatch
- B. Method B - Cross Hatch
- C. Method B - X cut
- D. Method A - X Cut
正解：D
質問 # 29
NACE Standards include:
- A. Material Requirements
- B. Standard Practices
- C. a) & b)
- D. a) only
正解：C
質問 # 30
The Inspectors' goal at the Pre-Job Conference is to:
- A. Discuss contractual requirements
- B. Take accurate meeting minutes for distribution
- C. Manage the meeting so it doesn't go off topic
- D. Obtain a clear understanding of the Specification
正解：D
質問 # 31
Surface preparation of concrete is performed using:
- A. Methods that are completely different to steel
- B. Methods that have been modified for concrete
- C. Methods that are exactly the same as steel
- D. Methods that are the same as wood
正解：B
質問 # 32
Thermal Spray coatings provide:
- A. Sacrificial protection
- B. Barrier protection
- C. Inhibitive protection
- D. Thermal protection
正解：A
質問 # 33
The most likely area of failure on a buried external pipeline coating is the:
- A. Areas exposed to Ultra Violet light
- B. Ground bed
- C. Field joint coating
- D. Mainline coating
正解：C
質問 # 34
Coating application to concrete substrates is:
- A. Less challenging, than coating steel
- B. More challenging than coating steel
- C. The same as coating steel
- D. Not required as Concrete is inorganic
正解：B
質問 # 35
An Inspection and Test Plan is required when:
- A. When the Coating Applicator requests one
- B. It is always required
- C. When the Inspector requests one
- D. When the Owner specifies one
正解：B
質問 # 36
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. False
- B. True
正解：B
質問 # 37
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only technical experts would understand
- B. Language that another NACE Inspector would understand
- C. Language that the most would understand
- D. Language that only in the project would understand
正解：C
質問 # 38
......
コーティングインスペクターレベル2の認定は、コーティング業界で最も権威のある認定の1つであると考えられています。これは、コーティング業界で最低2年の経験があり、コーティングインスペクターレベル1の認定を完了した個人を対象としています。レベル2の認定試験では、表面の準備、コーティングアプリケーション、品質管理、検査技術など、幅広いトピックをカバーしています。
NACE-CIP2-001問題集100パー合格保証には最新のサンプル：https://jp.fast2test.com/NACE-CIP2-001-premium-file.html
あなたを合格させる試験には100%確認済みNACE-CIP2-001試験問題：https://drive.google.com/open?id=1Dek76PiTzVjl4kDh2PBspIYIj6nJIq-o