[2025年03月20日]NACE-CIP2-001認定ガイド問題と解答トレーニング
NACE-CIP2-001認定お試しセット最新NACE-CIP2-001のPDF問題集
質問 # 16
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by acid etching
- B. SP 1 followed by caustic etching
- C. SP 1 followed by SP 3
- D. SP 1 followed by SP 2
正解：D
質問 # 17
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. Stoning
- B. Sacking
- C. High-pressure water washing
- D. Acid etching
正解：D
質問 # 18
Centrifugal blast cleaning requires:
- A. Well maintained blast wheels
- B. A large volume of air to propel the abrasive
- C. The use of single use abrasives
- D. Very large nozzles
正解：A
質問 # 19
Coating application to concrete substrates is:
- A. The same as coating steel
- B. Less challenging, than coating steel
- C. Not required as Concrete is inorganic
- D. More challenging than coating steel
正解：D
質問 # 20
When environmental enclosures are being used an inspector needs to be concerned about:
- A. Air changes
- B. Structural integrity
- C. a), b), and c)
- D. Lighting
正解：C
質問 # 21
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Defend the previous inspector
- B. Express a willingness to work with the site team and follow the specification
- C. Suggest to the Owner that the supervisor should be removed from site
- D. Challenge the supervisor's authority
正解：B
質問 # 22
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Slightly different to air blast cleaning
- B. Different than air blast cleaning
- C. Comparable to air blast cleaning
- D. The same as air blast cleaning
正解：D
質問 # 23
Antifouling coatings are regulated by international treaties.
- A. False
- B. True
正解：B
質問 # 24
Generally for safety considerations, waterjetting hose connections use
- A. an oil/water separator.
- B. a long wand.
- C. a whip-lock device.
- D. filters.
正解：C
質問 # 25
All of these are advantages of using repair patches EXCEPT
- A. barrier to moisture and corrosion.
- B. special tools or equipment are required.
- C. excellent abrasion resistance.
- D. inert to common acids, alkalis, and solvents.
正解：B
質問 # 26
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Flow stage
- B. Cure stage
- C. Gel stage
- D. Wetting stage
正解：A
質問 # 27
Surface preparation methods for Non-ferrous metals are:
- A. The same as for Ferrous metals
- B. Not required
- C. Specific for each type of Non-ferrous metal
- D. The same for all Non-FetT0us metals
正解：C
質問 # 28
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Conductive coatings applied to a magnetic metallic substrate
- B. Magnetic coatings applied to a magnetic metallic substrate
- C. Non-Conductive coatings applied to a conductive metallic substrate
- D. Conductive coatings applied to a cementitious substrate
正解：C
質問 # 29
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. powder coatings.
- B. urethanes.
- C. inorganic zincs.
- D. epoxies.
正解：C
質問 # 30
Inspector reports should always be copied to:
- A. All parties involved in the project
- B. Whomever the Owner identifies
- C. The Contractor and Owner
- D. The Owner only
正解：B
質問 # 31
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Verbally challenge the NCR
- B. Review the NCR with the other Inspector
- C. Consult your supervisor
- D. Request a re-blast of the item in question
正解：C
質問 # 32
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. A very high reading
- B. A very low reading
- C. Cold flow or creep
- D. No difference from any other coating
正解：C
質問 # 33
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Develop your own methodology and proceed take the readings
- B. Refuse to take readings until an is in place
- C. Call your supervisor
- D. Use a generally accepted industry standard and to take readings
正解：D
質問 # 34
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Supervision Costs
- B. Lower Safety Enforcement Costs
- C. Lower Application Costs
- D. Lower Coating Life Cycle Costs
正解：D
質問 # 35
......
ベストNACE NACE-CIP2-001学習ガイドと問題集は2025：https://jp.fast2test.com/NACE-CIP2-001-premium-file.html
トップクラスNACE NACE-CIP2-001試験最先端学習ガイド！練習問題バージョン：https://drive.google.com/open?id=1qCJk8w32W1D8YJbUVoD39Fx4bzfmmVti