NACEは2023年最新のNACE-CIP2-001テスト解説（更新されたのは100問があります)
NACE-CIP2-001試験問題集を提供していますNACE問題
NACE-CIP2-001試験には、コーティング仕様や基準、表面処理、コーティングの施工方法、検査技術、防食など、幅広いトピックが含まれています。合格者はまた、プロジェクト仕様書、図面、検査報告書などの技術文書を解釈する能力を示す必要があります。
NACE-CIP2-001試験は、塗装および腐食防止産業で働く個人にとって重要な認証です。認定を受けた個人は、知識と専門知識を証明することによって、キャリアを進め、雇用主にとっての価値を高めることができます。
質問 # 21
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Conductive coatings applied to a magnetic metallic substrate
- B. Non-Conductive coatings applied to a conductive metallic substrate
- C. Magnetic coatings applied to a magnetic metallic substrate
- D. Conductive coatings applied to a cementitious substrate
正解：B
質問 # 22
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Supervision Costs
- B. Lower Application Costs
- C. Lower Safety Enforcement Costs
- D. Lower Coating Life Cycle Costs
正解：D
質問 # 23
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Re-create the reports as not much was going on during night shift anyway
- B. Use creative writing to cover over the fact they are missing
- C. Plainly state in your report that they are missing
- D. Do not complete your report until they can be found
正解：C
質問 # 24
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. epoxies.
- B. inorganic zincs.
- C. powder coatings.
- D. urethanes.
正解：B
質問 # 25
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Ultra Sonic DFT Gauge
- B. Tooke Gauge
- C. Eddy Current Gauge
- D. Magnetic Gauge
正解：B
質問 # 26
Corrosion is the reverse process of
- A. galvanic deterioration.
- B. hot dipping.
- C. flaking.
- D. steel manufacturing.
正解：D
質問 # 27
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. False
- B. True
正解：A
質問 # 28
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Ignore the situation
- B. Advise the Owner and write a Non-Conformance report
- C. Require the Applicator to remove the coating
- D. Stop the job
正解：C
質問 # 29
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. 2-Layet Polyethylene (PE)
- B. 3-Layet Polyethylene (PE)
- C. Concrete
- D. Coal Tar Enamel
正解：C
質問 # 30
In which type of concrete are laitance commonly encountered?
- A. Glass fiber cement
- B. Concrete block (poured with a form)
- C. Gunite
- D. Poured (wet cast)
正解：D
質問 # 31
A reinforced coating is
- A. equally resistant to abrasion and impact as a non-reinforced coating.
- B. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. equally resistant to movement and impact as a non-reinforced coating.
- D. more resistant to movement, abrasion, and impact than a non-reinforced coating.
正解：D
質問 # 32
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Water Jetting Equipment
- B. Power Tools
- C. Abrasive Blasting Equipment
- D. Scarifiers
正解：A
質問 # 33
The primary purpose of Fireproofing coatings are to provide:
- A. Temporary protection for the structure
- B. Preferential fuel for the fire
- C. Explosion resistance
- D. fire extinguishing characteristics
正解：A
質問 # 34
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Suggest to the Owner that the supervisor should be removed from site
- B. Express a willingness to work with the site team and follow the specification
- C. Defend the previous inspector
- D. Challenge the supervisor's authority
正解：B
質問 # 35
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Different than air blast cleaning
- B. Slightly different to air blast cleaning
- C. The same as air blast cleaning
- D. Comparable to air blast cleaning
正解：C
質問 # 36
When observing fabrication defects the NACE Inspector should:
- A. Consult the specification to determine how they should be treated
- B. Require they be corrected prior to coating
- C. Stop the job immediately
- D. Write an NCR and call the fabricator
正解：A
質問 # 37
......
NACE-CIP2-001（Coating Inspector Level 2）認定試験は、コーティングシステムが必要な基準と仕様を満たしていることを確認する責任を持つコーティング産業の専門家にとって必須の認定資格です。この認定は、雇用者やクライアントの両方から高く評価される高度な専門知識と知識を証明します。
NACE-CIP2-001認定ガイドPDFは100%カバー率でリアル試験問題：https://jp.fast2test.com/NACE-CIP2-001-premium-file.html
合格させるNACE-CIP2-001レビューガイド、信頼され続けるNACE-CIP2-001テストエンジン：https://drive.google.com/open?id=1Dek76PiTzVjl4kDh2PBspIYIj6nJIq-o