[2024年02月25日]Fast2test NACE-CIP1-001問題集でCIP Level 1合格確定させる練習問題集
NACE NACE-CIP1-001実際にある問題とブレーン問題集
質問 # 49
Which one of these elements is not necessary for corrosion to occur:
- A. Anode
- B. Electrolyte
- C. Cathode
- D. Reference Cell
正解：D
質問 # 50
Inspection documentation is important because:
- A. a) & b)
- B. a) only
- C. Owners use the documentation for a variety of purposes
- D. It is the only deliverable item provided by the inspector
正解：C
質問 # 51
Daily reports are important because:
Select All That Apply
- A. the information impacts future projects.
- B. Inspectors rarely change on a project.
- C. Management uses them to make personnel decisions.
- D. The information aids communication with supervisors.
正解：A、C、D
質問 # 52
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Break the blisters to see what's inside
- B. Document the problem and advise the Contractor and Owner's representative
- C. Document the problem and advise the Contractor
- D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
正解：B
質問 # 53
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- C. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
正解：D
質問 # 54
To achieve consistently accurate results with ALL alt test equipment
- A. avoid placing the sample discs on a surface.
- B. calibrate the instrument in the field.
- C. wear gloves when sampling.
- D. wash your hands before sampling.
正解：D
質問 # 55
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. checking.
- B. cracking.
- C. sagging.
- D. holiday.
正解：D
質問 # 56
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Purchase Professional Liability Insurance prior to job commencement
- B. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- C. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- D. Meet with the owner and explain your limitations and concerns prior accepting the assignment
正解：C
質問 # 57
A NACE Coating Inspector is permitted to transport coating material when:
- A. Asked to do so by the Owner's Representative
- B. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- C. Asked to do so by the Coating Application team
- D. The Inspector should never transport coating material
正解：D
質問 # 58
Non Conformance Reports are completed by the Inspector:
- A. When the Inspector deems it to be a significant non-conforming item
- B. When the Inspector and Contractor deem it to be a significant non-conforming item
- C. In accordance with the specification's definition of a non-conformance
- D. In every instance that an item does not meet the specification requirements
正解：B
質問 # 59
Dew point is the temperature at which
- A. the air is saturated.
- B. humidity decreases
- C. water freezes.
- D. condensation occurs.
正解：D
質問 # 60
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 225 Gauge Readings resulting in 75 Spot Measurements
- B. 105 Gauge Readings resulting in 35 Spot Measurements
- C. 75 Gauge Readings resulting in 25 Spot Measurements
- D. 45 Gauge readings resulting in 15 Spot Measurements
正解：A
質問 # 61
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Review the NACE Attestation prior to making a decision
- B. Advise the prospective employer that you cannot accept the position
- C. Accept the assignment without hesitation
- D. Meet with the prospective employer to determine the scope of your role
正解：D
質問 # 62
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Surface Temperature
- B. Low Surface Temperature
- C. High Relative Humidity
- D. Low Relative Humidity
正解：D
質問 # 63
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. cracking.
- B. blistering.
- C. alligatoring.
- D. checking.
正解：D
質問 # 64
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Taking measurements too far from the edge of a surface
- B. Rotating the dial too fast when taking measurements
- C. Measuring ditty, tacky, or soft films
- D. Failing to determine the base metal reading (BMR)
正解：B、C、D
質問 # 65
Osmotic blistering is most likely to occur as a result of
- A. overcoating a surface contaminated with chemical salts.
- B. applying tine coating too thin.
- C. airless spray application
- D. inadequate anchor pattern/surface profile.
正解：C
質問 # 66
In a non-convertible coating the role of the primary solvent is to:
- A. To dissolve the resin
- B. To control the evaporation rate
- C. To promote faster cure
- D. To make the coating flow out better
正解：B
質問 # 67
An inspectors personal log book should contain:
- A. Subjective comments re ding the application team
- B. No comments regarding the application team
- C. Objective comments regarding the application work
- D. The inspector's personal opinions of the application team
正解：B
質問 # 68
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record your result by identifying two segments
- B. Record the segment with the less aggressive profile
- C. Use another method as the comparator method is too subjective
- D. Record the segment with the more aggressive profile
正解：B
質問 # 69
The least effective method of surface cleaning is most likely
- A. water blasting.
- B. dry grit blasting.
- C. hand tool cleaning.
- D. power tool cleaning.
正解：C
質問 # 70
......
NACE-CIP1-001試験に合格した個人は、基本的なコーティング検査タスクを実行する資格があると見なされます。コーティングの欠陥を特定し、基本的な表面準備を実行し、さまざまな環境でコーティングの適切な使用を認識できます。この認証は、石油とガス、海洋、インフラなどの産業で非常に評価されています。また、コーティングインスペクターとしてのキャリアを追求したい、または一般的なコーティング業界でのキャリアを追求したい個人にとっても優れた出発点です。
最新NACE-CIP1-001合格保証 試験問題集でには正確で最新な 問題：https://jp.fast2test.com/NACE-CIP1-001-premium-file.html
合格させるNACE-CIP1-001試験には最新なNACE-CIP1-001試験問題集PDF2024：https://drive.google.com/open?id=1mO_IuETAf9ovemWaimNpFnqiIaGzAAEV