2025年更新のNACE-CIP1-001問題集合格保証付きで合格できます！
NACE-CIP1-001試験問題集を試そう！ベストNACE-CIP1-001試験問題トレーニングを提供しています
質問 # 35
The Inspector's Log Book is generally:
- A. Shredded by the inspector upon project completion
- B. Submitted to the client upon project completion
- C. Shared with all parties upon project completion
- D. Retained by the inspector upon project completion
正解：D
質問 # 36
Inspection documentation is important because:
- A. Owners use the documentation for a variety of purposes
- B. a) only
- C. It is the only deliverable item provided by the inspector
- D. a) & b)
正解：A
質問 # 37
ISO ST 3 is described as:
- A. Very Thorough hand or power tool cleaning
- B. Very Thorough power tool cleaning
- C. Thorough hand tool cleaning
- D. Thorough blast cleaning
正解：A
質問 # 38
The most important factor resulting in improved job site safety is:
- A. Engineering Controls
- B. Personal Protective Equipment
- C. Safety Enforcement
- D. Situational Awareness
正解：D
質問 # 39
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 2
- B. Level 3
- C. Level 4
- D. Level 1
正解：B
質問 # 40
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Use another method as the comparator method is too subjective
- B. Record your result by identifying two segments
- C. Record the segment with the more aggressive profile
- D. Record the segment with the less aggressive profile
正解：D
質問 # 41
Which one of the following documents is the best source for coating technical data:
- A. Technical Data Sheet
- B. Safety Data Sheet;
- C. Application Guidelines
- D. Specification
正解：A
質問 # 42
ISO SA 2.5 is defined as:
- A. Thorough Blast Cleaning
- B. Light Blast Cleaning
- C. Very Thorough Blast Cleaning
- D. Near White Metal Blasting
正解：C
質問 # 43
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Permit coating to take place so as not to lose the blast
- B. Call your supervisor
- C. Review the relevant standard with the Contractor
- D. Shut the job down
正解：C
質問 # 44
The least effective method of surface cleaning is most likely
- A. hand tool cleaning.
- B. dry grit blasting.
- C. power tool cleaning.
- D. water blasting.
正解：A
質問 # 45
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
正解：A
質問 # 46
A successful coating inspector must be able to
- A. advise the coating applicator on how to mix the coating.
- B. apply the coating with expert accuracy.
- C. look for problems or issues during application.
- D. recommend the appropriate coating technique for the job to the contractor.
正解：C
質問 # 47
Solvents are added to coating formulations to
- A. provide color.
- B. decrease film permeability.
- C. dissolve binders and form liquid coatings.
- D. increase film permeability.
正解：C
質問 # 48
Which is a component that supplies most of the features and functions of the material?
- A. additive
- B. pigment
- C. binder
- D. solvent
正解：C
質問 # 49
Stripe coats are generally applied to:
- A. Edges and corners
- B. a), b), and c)
- C. Welds
- D. Complex geometric shapes
正解：B
質問 # 50
The initial steel condition is important to the NACE Inspector because:
- A. Less abrasive is need if the mill Scale s gone
- B. The Inspector may have to reject the Steel
- C. It affects the final appearance after blasting
- D. If the steel is pitted more coating will be required
正解：B
質問 # 51
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 10 to 12 mils (250 to 300 microns)
- B. 6 to 7 mils (150 to 175 microns)
- C. 8 to 10 mils (200 to 250 microns)
- D. 5 to 6 mils (125 to 150 microns)
正解：B
質問 # 52
Check abrasive blast pressure with a
- A. needle pressure gauge
- B. replica tape
- C. nozzle aperature gauge
- D. surface comparator
正解：A
質問 # 53
Daily reports are important because:
Select All That Apply
- A. The information aids communication with supervisors.
- B. Inspectors rarely change on a project.
- C. Management uses them to make personnel decisions.
- D. the information impacts future projects.
正解：A、C、D
質問 # 54
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the credentials of the Safety Officer on site
- B. Check the PPE used by the Applicators
- C. Act in accordance with the site safety requirements and set an example
- D. Assume the role of the Safety Inspector
正解：C
質問 # 55
If a Thermoset coating is heated it will:
- A. Harden and retain its hardness when cooled
- B. Soften when heated and retain its softness when cooled
- C. Soften when heated and return to its original hardness when cooled
- D. Harden and return to its original hardness when cooled
正解：A
質問 # 56
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
正解：D
質問 # 57
......
最新100%合格率保証付きの素晴らしいNACE-CIP1-001試験問題PDF：https://jp.fast2test.com/NACE-CIP1-001-premium-file.html
実践サンプルと問題集指導には2025年最新のNACE-CIP1-001有効なテスト問題集：https://drive.google.com/open?id=16KjpddwjPClzaQ4JzgWaLLU8byll_7iK