2024年最新のに更新されたのはNACE-CIP1-001テストエンジンとPDFで完全版無料問題集保証！
最新のCIP Level 1 NACE-CIP1-001実際の無料試験問題
NACE-CIP1-001試験は、コーティング検査のすべての側面をカバーする包括的な試験です。この試験は、コーティングの品質を評価するために使用される方法と技術など、個人がコーティング検査の原則と実践を確実に理解できるように設計されています。この試験では、さまざまな業界で使用されるコーティングの種類と、コーティングの性能に影響を与える可能性のある要因もカバーしています。
NACE-CIP1-001試験は、コーティング検査の分野で働くプロフェッショナル向けに、全米腐食工学協会（NACE）が提供する認定プログラムです。この試験は、入門レベルのコーティング検査員の知識とスキルをテストするために設計されており、この分野でキャリアを進めたい方にとって貴重な資格となります。
質問 # 33
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- B. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- C. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- D. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
正解：C
質問 # 34
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. white metal blast cleaning.
- B. commercial blast cleaning.
- C. brush-off blast cleaning.
- D. near-white metal blast cleaning.
正解：C
質問 # 35
Passivation can best be described as:
- A. Treating metal with a liquid inhibiter
- B. A coating layer applied to the surface to inhibit corrosion
- C. A protective metallic oxide surface layer that slows corrosion
- D. Complete elimination pf the corrosion process
正解：C
質問 # 36
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. sulfates
- B. grease and oil
- C. inhibitor residues
- D. soluble chemical salts
正解：B
質問 # 37
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- B. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- C. Bring the matter up at the pre-job conference
- D. Default to the owner's Inspection and Test Plan
正解：C
質問 # 38
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Relative Humidity
- B. Low Surface Temperature
- C. Low Relative Humidity
- D. High Surface Temperature
正解：C
質問 # 39
Stripe coats are generally applied to:
- A. Edges and corners
- B. a), b), and c)
- C. Complex geometric shapes
- D. Welds
正解：B
質問 # 40
To be of value the Inspector's documentation must be:
- A. Timely, accurate and concise
- B. Always handwritten
- C. Always typewritten
- D. Submitted before the end of the job
正解：A
質問 # 41
Removal of surface contaminants is done by:
- A. Scarifying
- B. A combination of methods
- C. Waterjetting
- D. Abrasive blasting
正解：B
質問 # 42
Polymerization is the process of:
- A. Monomers telegraphing
- B. All thermoplastic coatings
- C. All organic coatings
- D. Monomers joining together
正解：D
質問 # 43
Which one of these elements is not necessary for corrosion to occur:
- A. Anode
- B. Reference Cell
- C. Cathode
- D. Electrolyte
正解：B
質問 # 44
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 100% of the specified maximum thickness
- B. 80% of the specified minimum thickness
- C. 90% of the specified maximum thickness
- D. 70% of the specified maximum thickness
正解：B
質問 # 45
According to SSPC PA 2 a Spot Measurement is:
- A. The overall average of all readings
- B. The average of gauge readings taken in a 4cm (1.5 inch) circle
- C. A single gauge reading
- D. The average of all spot measurements in a given area
正解：B
質問 # 46
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:
- A. monitoring
- B. telegraphing.
- C. juxtaposing.
- D. transitioning.
正解：B
質問 # 47
Safety Data Sheets must be carefully reviewed by:
- A. The Inspection personnel
- B. The Application personnel
- C. The Owner's personnel
- D. All personnel involved in the job
正解：D
質問 # 48
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. holiday.
- B. cracking.
- C. sagging.
- D. checking.
正解：A
質問 # 49
The most important factor resulting in improved job site safety is:
- A. Situational Awareness
- B. Safety Enforcement
- C. Personal Protective Equipment
- D. Engineering Controls
正解：A
質問 # 50
......
NACE-CIP1-001認定試験を受ける資格を得るには、個人が特定の要件を満たす必要があります。これらの要件には、コーティング業界または関連分野で少なくとも6か月の経験があること、NACEが承認したトレーニングコースの完了、およびNACEに完了したアプリケーションを提出することが含まれます。個人がこれらの要件を満たし、認定試験に合格すると、NACE-CIP1-001認定が授与されます。
NACE-CIP1-001問題集には更新された練習テストと100独特な問題：https://jp.fast2test.com/NACE-CIP1-001-premium-file.html
最新の100%試験合格率爆上がり NACE-CIP1-001問題集PDF：https://drive.google.com/open?id=1t4oZn_QDoxfEbPP79cDXc-wqtIwsHTpK