[2025年03月06日]NACE-CIP1-001試験問題集を試そう！ベストNACE-CIP1-001試験問題
検証済みのNACE-CIP1-001テスト問題集で正確な100問題と解答
NACE-CIP1-001認定は、業界で非常に尊敬されており、世界中の雇用主によって認められています。この認定は、コーティング検査と腐食制御に関する個人の専門知識を示しており、あらゆる組織にとって貴重な資産となっています。腐食制御の専門家の需要が増加し続けるにつれて、NACE-CIP1-001認定を取得すると、新しいキャリアの機会とより高い収益の可能性につながる可能性があります。
NACE-CIP1-001試験に合格するには、候補者はNACE承認のトレーニングプログラムの修了または塗装業界での最低6か月間の経験を含む特定の要件を満たす必要があります。この試験は、世界中の腐食制御専門家のためのトレーニング、認証、および標準開発を提供する主要な組織であるNACE Internationalによって実施されます。
質問 # 44
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which power tool the Contractor selects
- B. No, because there is no real difference in the standards
- C. It depends on which hand tool the Contractor selects
- D. Yes, because the 'two standards are not equivalent
正解：B
質問 # 45
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Purchase Professional Liability Insurance prior to job commencement
- B. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- C. Meet with the owner and explain your limitations and concerns prior accepting the assignment
- D. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
正解：B
質問 # 46
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the less aggressive profile
- B. Record your result by identifying two segments
- C. Use another method as the comparator method is too subjective
- D. Record the segment with the more aggressive profile
正解：A
質問 # 47
Removal of surface contaminants is done by:
- A. Scarifying
- B. Abrasive blasting
- C. Waterjetting
- D. A combination of methods
正解：D
質問 # 48
Prior to using Inspection Tools the inspector must:
- A. Ensure the instrument is within calibration parameters
- B. Be trained on how to use the instrument
- C. Read the manufactures' instructions
- D. a), b) & c)
正解：D
質問 # 49
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Go with the majority opinion
- B. Achieve consensus through negotiation
- C. Never change his/her mind
- D. Call the supervisor
正解：D
質問 # 50
ISO SA 2 is defined as:
- A. Thorough Blast Cleaning
- B. Near White Metal Blasting
- C. Very Thorough Blast Cleaning
- D. Light Blast Cleaning
正解：A
質問 # 51
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. SSPC PA 2
- B. NACE SP 0178
- C. NACE SP 0188
- D. SSPC-CS 23.00/AWS C2.23/NACE No. 12
正解：D
質問 # 52
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Airless spray equipment
- B. Power tools
- C. Abrasive blast nozzles
- D. Hand tools
正解：B
質問 # 53
The most important factor resulting in improved job site safety is:
- A. Engineering Controls
- B. Safety Enforcement
- C. Situational Awareness
- D. Personal Protective Equipment
正解：C
質問 # 54
Non Conformance Reports are completed by the Inspector:
- A. In every instance that an item does not meet the specification requirements
- B. When the Inspector and Contractor deem it to be a significant non-conforming item
- C. When the Inspector deems it to be a significant non-conforming item
- D. In accordance with the specification's definition of a non-conformance
正解：B
質問 # 55
Solvents are added to coating formulations to
- A. decrease film permeability.
- B. provide color.
- C. increase film permeability.
- D. dissolve binders and form liquid coatings.
正解：D
質問 # 56
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Atmospheric Corrosion
- B. General Corrosion
- C. Galvanic Corrosion
- D. Localized Corrosion
正解：C
質問 # 57
Daily reports are important because:
Select All That Apply
- A. Management uses them to make personnel decisions.
- B. the information impacts future projects.
- C. Inspectors rarely change on a project.
- D. The information aids communication with supervisors.
正解：A、B、D
質問 # 58
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. scratches the surface too deeply resulting in uneven coating application
- B. develops a good anchor profile resulting in uneven coating application.
- C. develops a polished surface, which is a poor anchor profile for most coatings
- D. damages structural elements thereby speeding up the corrosion process.
正解：C
質問 # 59
An inspectors personal log book should contain:
- A. Objective comments regarding the application work
- B. No comments regarding the application team
- C. The inspector's personal opinions of the application team
- D. Subjective comments re ding the application team
正解：B
質問 # 60
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 100% of the specified maximum thickness
- B. 80% of the specified minimum thickness
- C. 70% of the specified maximum thickness
- D. 90% of the specified maximum thickness
正解：B
質問 # 61
If inspectors identify issues of non-conformance during an inspection, they should
- A. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- B. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- C. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- D. perform additional tests secretly to ensure there are no other potential issues at the site
正解：B
質問 # 62
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. Pass/fail criteria
- B. A general guide
- C. A final conflict resolution method
- D. A method to grade surface profile
正解：B
質問 # 63
Relative humidity is
- A. the lowest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to saturation level.
- C. the highest temperature at which moisture forms on a steel surface.
- D. a measure of the amount of moisture in the air compared to the air temperature.
正解：B
質問 # 64
Safety Data Sheets must be carefully reviewed by:
- A. All personnel involved in the job
- B. The Inspection personnel
- C. The Owner's personnel
- D. The Application personnel
正解：A
質問 # 65
Digital hygrometers
- A. use a thermocouple in contact with the surface to measure temperature
- B. are used to measure temperature from a distance.
- C. determine relative humidity, air temperature, and dew point temperature:
- D. consist of a bimetallic sensing element protected from wind gusts.
正解：C
質問 # 66
Corrosion generally occurs at which of the following sites:
- A. Cathode
- B. Metallic pathway
- C. Electrolyte
- D. Anode
正解：D
質問 # 67
Stripe coats are best applied by:
- A. High volume low pressure spray
- B. Airless spray
- C. Conventional spray
- D. Brush
正解：D
質問 # 68
......
認定は発行後3年間有効です。この期間後、再認証が必要です。専門家は、関連する分野のトレーニングや教育クレジットを修了し、再認証のための職務経験基準を満たす必要があります。再認証により、認定された個人が業界標準に従い、NACE倫理規定に従うことが確認されます。
NACE NACE-CIP1-001テストエンジンPDFで全問 無料問題集：https://jp.fast2test.com/NACE-CIP1-001-premium-file.html
手に入れよう！最新NACE-CIP1-001認定有効な試験問題集解答：https://drive.google.com/open?id=16KjpddwjPClzaQ4JzgWaLLU8byll_7iK