NACE NACE-CIP1-001リアルに2025年最新のブレーン問題集で模擬試験問題集
NACE-CIP1-001試験問題 リアルなNACE-CIP1-001練習問題集
NACE-CIP1-001（コーティングインスペクターレベル1）認定試験は、全米腐食エンジニア協会（NACE）が提供する世界的に認められた認定です。この認証は、産業環境でのコーティングと腐食制御の検査に関与している個人向けに設計されています。この試験では、コーティング検査、表面の準備、コーティングの適用、腐食防止など、さまざまなトピックをカバーしています。
NACE-CIP1-001（コーティングインスペクターレベル1）認定試験は、認定コーティング検査官になるために必要な知識とスキルを個人に提供するように設計された専門的な認定プログラムです。この認証は、腐食防止と制御に焦点を当てた専門組織である全米腐食エンジニア協会（NACE）によって提供されています。
質問 # 35
An Inspector should change position when:
- A. The Owner can save some money by the change
- B. The Inspector is convinced by verifiable facts
- C. The Inspectors position is not the majority position
- D. Only when directed by the supervisor
正解：B
質問 # 36
Inspector's daily reports are used:
Select All That Apply
- A. To help in cases of a coating failure
- B. By the contractor to estimate the amount of work done that day
- C. To provide continuity between inspectors
- D. To aid in arbitration between the contractor and client
正解：A、B、C、D
質問 # 37
ISO ST 3 is described as:
- A. Very Thorough hand or power tool cleaning
- B. Very Thorough power tool cleaning
- C. Thorough hand tool cleaning
- D. Thorough blast cleaning
正解：A
質問 # 38
Relative humidity is
- A. the highest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to the air temperature.
- C. the lowest temperature at which moisture forms on a steel surface.
- D. a measure of the amount of moisture in the air compared to saturation level.
正解：D
質問 # 39
Which one of these elements is not necessary for corrosion to occur:
- A. Reference Cell
- B. Cathode
- C. Anode
- D. Electrolyte
正解：A
質問 # 40
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- B. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- C. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- D. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
正解：C
質問 # 41
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which hand tool the Contractor selects
- B. It depends on which power tool the Contractor selects
- C. No, because there is no real difference in the standards
- D. Yes, because the 'two standards are not equivalent
正解：C
質問 # 42
Check abrasive blast pressure with a
- A. nozzle aperature gauge
- B. replica tape
- C. needle pressure gauge
- D. surface comparator
正解：C
質問 # 43
An inspectors personal log book should contain:
- A. Subjective comments re ding the application team
- B. No comments regarding the application team
- C. Objective comments regarding the application work
- D. The inspector's personal opinions of the application team
正解：B
質問 # 44
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks and consult the Owner's representative for direction
- B. Skip the checks and just record the same readings as you have been getting
- C. Skip the checks as you are. confident the blast pressure is OK
- D. Keep doing the checks regardless
正解：A
質問 # 45
If inspectors identify issues of non-conformance during an inspection, they should
- A. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- B. perform additional tests secretly to ensure there are no other potential issues at the site
- C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- D. wait until the final report is being prepared to identify the issues in writing so they are fully documented
正解：C
質問 # 46
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
正解：C
質問 # 47
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. brush-off blast cleaning.
- B. commercial blast cleaning.
- C. near-white metal blast cleaning.
- D. white metal blast cleaning.
正解：A
質問 # 48
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 100% of the specified maximum thickness
- B. 70% of the specified maximum thickness
- C. 80% of the specified minimum thickness
- D. 90% of the specified maximum thickness
正解：C
質問 # 49
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to, be Lined for Immersion Service
- B. Structural steel to be coated for Atmospheric Service
- C. Stainless steel pipe to be Externally Coated
- D. Tanks and Vessels to be Externally Coated
正解：A
質問 # 50
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Failing to determine the base metal reading (BMR)
- B. Measuring ditty, tacky, or soft films
- C. Rotating the dial too fast when taking measurements
- D. Taking measurements too far from the edge of a surface
正解：A、B、C
質問 # 51
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. vial lest.
- B. wet film thickness (WFT) measurement.
- C. dry film thickness (DEI) measurement.
- D. blotter test for the presence of oil and water.
正解：D
質問 # 52
The initial steel condition is important to the NACE Inspector because:
- A. It affects the final appearance after blasting
- B. If the steel is pitted more coating will be required
- C. The Inspector may have to reject the Steel
- D. Less abrasive is need if the mill Scale s gone
正解：C
質問 # 53
You ate the NACE Inspector on a job where NACE No. 2/SSPC - SP 10 has been specified. You are finding the Contractor is leaving mill scale on the on surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mill scale to remain and still be in be in compliance with the standard.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Review the relevant standard with the Contractor
- C. Shut the job down
- D. Permit coating to take place so as not to lose the blast
正解：B
質問 # 54
To achieve consistently accurate results with ALL alt test equipment
- A. wash your hands before sampling.
- B. calibrate the instrument in the field.
- C. wear gloves when sampling.
- D. avoid placing the sample discs on a surface.
正解：A
質問 # 55
......
厳密検証されたNACE-CIP1-001試験問題集と解答で無料提供のNACE-CIP1-001問題と正解付き：https://jp.fast2test.com/NACE-CIP1-001-premium-file.html
あなたを合格させるNACE-CIP1-001問題集無料で最新のNACE練習テスト：https://drive.google.com/open?id=16KjpddwjPClzaQ4JzgWaLLU8byll_7iK