[2025年04月] 更新されたのはNACE NACE-CIP1-001問題集PDFオンラインエンジン
NACE-CIP1-001.PDFで問題解答PDFサンプル問題は信頼され続ける
質問 # 43
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. grease and oil
- B. sulfates
- C. soluble chemical salts
- D. inhibitor residues
正解：A
質問 # 44
An Inspector should change position when:
- A. Only when directed by the supervisor
- B. The Owner can save some money by the change
- C. The Inspectors position is not the majority position
- D. The Inspector is convinced by verifiable facts
正解：D
質問 # 45
The Inspector's Log Book is generally:
- A. Shared with all parties upon project completion
- B. Retained by the inspector upon project completion
- C. Submitted to the client upon project completion
- D. Shredded by the inspector upon project completion
正解：B
質問 # 46
Check abrasive blast pressure close to the
- A. substrate
- B. compressor
- C. blast pot
- D. blast nozzle
正解：D
質問 # 47
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. No, because there is no real difference in the standards
- B. It depends on which hand tool the Contractor selects
- C. It depends on which power tool the Contractor selects
- D. Yes, because the 'two standards are not equivalent
正解：A
質問 # 48
Solvents are added to coating formulations to
- A. provide color.
- B. increase film permeability.
- C. dissolve binders and form liquid coatings.
- D. decrease film permeability.
正解：C
質問 # 49
An inspectors personal log book should contain:
- A. Objective comments regarding the application work
- B. No comments regarding the application team
- C. The inspector's personal opinions of the application team
- D. Subjective comments re ding the application team
正解：B
質問 # 50
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. dry film thickness (DEI) measurement.
- B. vial lest.
- C. wet film thickness (WFT) measurement.
- D. blotter test for the presence of oil and water.
正解：D
質問 # 51
A successful coating inspector must be able to
- A. advise the coating applicator on how to mix the coating.
- B. look for problems or issues during application.
- C. recommend the appropriate coating technique for the job to the contractor.
- D. apply the coating with expert accuracy.
正解：B
質問 # 52
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. False
- B. True
正解：B
質問 # 53
Non Conformance Reports are completed by the Inspector:
- A. When the Inspector deems it to be a significant non-conforming item
- B. When the Inspector and Contractor deem it to be a significant non-conforming item
- C. In accordance with the specification's definition of a non-conformance
- D. In every instance that an item does not meet the specification requirements
正解：B
質問 # 54
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Use the product data sheet as a guide
- B. Use the job specification as a guide
- C. Call the person who wrote the specification for clarification
- D. Call the coating manufacturer for clarification
正解：B
質問 # 55
In a non-convertible coating the role of the primary solvent is to:
- A. To make the coating flow out better
- B. To control the evaporation rate
- C. To dissolve the resin
- D. To promote faster cure
正解：B
質問 # 56
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. when the coating will be reapplied.
- B. what materials were used.
- C. how the item was coated.
- D. what items were coated.
正解：C
質問 # 57
Which one of the following documents is the best source for coating technical data:
- A. Specification
- B. Technical Data Sheet
- C. Application Guidelines
- D. Safety Data Sheet;
正解：B
質問 # 58
Digital hygrometers
- A. are used to measure temperature from a distance.
- B. use a thermocouple in contact with the surface to measure temperature
- C. consist of a bimetallic sensing element protected from wind gusts.
- D. determine relative humidity, air temperature, and dew point temperature:
正解：D
質問 # 59
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 105 Gauge Readings resulting in 35 Spot Measurements
- B. 225 Gauge Readings resulting in 75 Spot Measurements
- C. 75 Gauge Readings resulting in 25 Spot Measurements
- D. 45 Gauge readings resulting in 15 Spot Measurements
正解：B
質問 # 60
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Default to the owner's Inspection and Test Plan
- B. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- C. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- D. Bring the matter up at the pre-job conference
正解：D
質問 # 61
ISO ST 3 is described as:
- A. Thorough hand tool cleaning
- B. Very Thorough hand or power tool cleaning
- C. Very Thorough power tool cleaning
- D. Thorough blast cleaning
正解：B
質問 # 62
......
NACE NACE-CIP1-001問題集PDFのベストを目指すなら問題集を使おう 目指そう高得点：https://jp.fast2test.com/NACE-CIP1-001-premium-file.html
CIP Level 1 NACE-CIP1-001試験と認定テストエンジン：https://drive.google.com/open?id=1t4oZn_QDoxfEbPP79cDXc-wqtIwsHTpK