2025年最新の有効なNACE-CIP1-001リアル試験問題（更新された）100%問題集と練習試験合格させます
[更新されたのは2025年]NACE NACE-CIP1-001問題準備には無料サンプルのPDF
NACE-CIP1-001認定試験を受ける資格を得るには、個人が特定の要件を満たす必要があります。これらの要件には、コーティング業界または関連分野で少なくとも6か月の経験があること、NACEが承認したトレーニングコースの完了、およびNACEに完了したアプリケーションを提出することが含まれます。個人がこれらの要件を満たし、認定試験に合格すると、NACE-CIP1-001認定が授与されます。
NACE-CIP1-001（コーティングインスペクターレベル1）認定試験は、認定コーティング検査官になるために必要な知識とスキルを個人に提供するように設計された専門的な認定プログラムです。この認証は、腐食防止と制御に焦点を当てた専門組織である全米腐食エンジニア協会（NACE）によって提供されています。
質問 # 28
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the PPE used by the Applicators
- B. Act in accordance with the site safety requirements and set an example
- C. Check the credentials of the Safety Officer on site
- D. Assume the role of the Safety Inspector
正解：B
質問 # 29
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Use another method as the comparator method is too subjective
- B. Record the segment with the less aggressive profile
- C. Record the segment with the more aggressive profile
- D. Record your result by identifying two segments
正解：B
質問 # 30
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. cracking.
- B. checking.
- C. blistering.
- D. alligatoring.
正解：B
質問 # 31
Inspection documentation is important because:
- A. a) & b)
- B. Owners use the documentation for a variety of purposes
- C. a) only
- D. It is the only deliverable item provided by the inspector
正解：B
質問 # 32
Silicone coatings are typically:
- A. Applied in very thick films
- B. Applied in very' thin films
- C. Used as a sacrificial primer
- D. Used strictly in immersion service
正解：B
質問 # 33
Surface profile describes:
- A. The general condition of the surface required after abrasive blasting
- B. The level of surface cleanliness required after abrasive blasting
- C. The initial condition of the surface prior to abrasive blasting
- D. The level of surface roughness required after abrasive blasting
正解：D
質問 # 34
The initial steel condition is important to the NACE Inspector because:
- A. If the steel is pitted more coating will be required
- B. The Inspector may have to reject the Steel
- C. Less abrasive is need if the mill Scale s gone
- D. It affects the final appearance after blasting
正解：B
質問 # 35
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. NACE SP 0188
- B. SSPC PA 2
- C. NACE SP 0178
- D. SSPC-CS 23.00/AWS C2.23/NACE No. 12
正解：D
質問 # 36
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Dragging a gauge through wet coating
- B. Using a damaged gauge
- C. Placing the gauge along the longitudinal axis
正解：A、B
質問 # 37
The least effective method of surface cleaning is most likely
- A. hand tool cleaning.
- B. water blasting.
- C. power tool cleaning.
- D. dry grit blasting.
正解：A
質問 # 38
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- C. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
正解：D
質問 # 39
Osmotic blistering is most likely to occur as a result of
- A. applying tine coating too thin.
- B. airless spray application
- C. inadequate anchor pattern/surface profile.
- D. overcoating a surface contaminated with chemical salts.
正解：B
質問 # 40
ASTM Standards are applicable:
- A. When specified
- B. In Asia
- C. In the USA
- D. In North America
正解：A
質問 # 41
The main responsibilities of the inspector are to
- A. direct and perform the work stated in the specification.
- B. observe and report the quality of the work performed.
- C. observe and direct the work of the contractors.
- D. demonstrate to the contractor how to apply the coating.
正解：B
質問 # 42
Checking is
- A. an exposed area of the substrate or previous coat material, caused by poor application technique.
- B. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- C. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- D. a fine crack in the surface of a coating that rarely reaches the substrate
正解：D
質問 # 43
An inspectors personal log book should contain:
- A. No comments regarding the application team
- B. Objective comments regarding the application work
- C. The inspector's personal opinions of the application team
- D. Subjective comments re ding the application team
正解：A
質問 # 44
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. soluble chemical salts
- B. sulfates
- C. inhibitor residues
- D. grease and oil
正解：D
質問 # 45
Daily reports are important because:
Select All That Apply
- A. The information aids communication with supervisors.
- B. Inspectors rarely change on a project.
- C. the information impacts future projects.
- D. Management uses them to make personnel decisions.
正解：A、C、D
質問 # 46
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Relative Humidity
- B. High Surface Temperature
- C. Low Relative Humidity
- D. Low Surface Temperature
正解：C
質問 # 47
......
NACE-CIP1-001豪華セット学習ガイドにはオンライン試験エンジン：https://jp.fast2test.com/NACE-CIP1-001-premium-file.html
2025年最新の認定サンプル問題NACE-CIP1-001問題集と練習試験：https://drive.google.com/open?id=1t4oZn_QDoxfEbPP79cDXc-wqtIwsHTpK