NACE-CIP1-001試験問題集合格させるのは2024年最新の認証済み試験問題
NACE-CIP1-001試験問題でリアルに更新された問題PDF
質問 # 30
Polymerization is the process of:
- A. Monomers telegraphing
- B. All thermoplastic coatings
- C. Monomers joining together
- D. All organic coatings
正解：C
質問 # 31
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Keep doing the checks and consult the Owner's representative for direction
- B. Skip the checks and just record the same readings as you have been getting
- C. Skip the checks as you are. confident the blast pressure is OK
- D. Keep doing the checks regardless
正解：A
質問 # 32
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. SSPC-CS 23.00/AWS C2.23/NACE No. 12
- B. NACE SP 0178
- C. NACE SP 0188
- D. SSPC PA 2
正解：A
質問 # 33
ISO SA 2.5 is defined as:
- A. Thorough Blast Cleaning
- B. Near White Metal Blasting
- C. Very Thorough Blast Cleaning
- D. Light Blast Cleaning
正解：C
質問 # 34
Check abrasive blast pressure close to the
- A. blast nozzle
- B. compressor
- C. blast pot
- D. substrate
正解：A
質問 # 35
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Placing the gauge along the longitudinal axis
- B. Using a damaged gauge
- C. Dragging a gauge through wet coating
正解：B、C
質問 # 36
Passivation can best be described as:
- A. A protective metallic oxide surface layer that slows corrosion
- B. Treating metal with a liquid inhibiter
- C. Complete elimination pf the corrosion process
- D. A coating layer applied to the surface to inhibit corrosion
正解：A
質問 # 37
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. High Surface Temperature
- B. Low Relative Humidity
- C. High Relative Humidity
- D. Low Surface Temperature
正解：B
質問 # 38
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 75 Gauge Readings resulting in 25 Spot Measurements
- B. 45 Gauge readings resulting in 15 Spot Measurements
- C. 105 Gauge Readings resulting in 35 Spot Measurements
- D. 225 Gauge Readings resulting in 75 Spot Measurements
正解：D
質問 # 39
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor and Owner's representative
- B. Document the problem and advise the Contractor
- C. Break the blisters to see what's inside
- D. Extract any liquid that may be inside the blister and send it to the lab for further analysis
正解：A
質問 # 40
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 70% of the specified maximum thickness
- C. 100% of the specified maximum thickness
- D. 90% of the specified maximum thickness
正解：A
質問 # 41
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
- B. Advise the owners' representative of your lack of knowledge in this area
- C. Hire a third patty to assist you in understanding the document
- D. Carefully review the document and do the best you can
正解：D
質問 # 42
To be of value the Inspector's documentation must be:
- A. Timely, accurate and concise
- B. Submitted before the end of the job
- C. Always handwritten
- D. Always typewritten
正解：A
質問 # 43
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to be Externally Coated
- B. Structural steel to be coated for Atmospheric Service
- C. Tanks and Vessels to, be Lined for Immersion Service
- D. Stainless steel pipe to be Externally Coated
正解：C
質問 # 44
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- D. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
正解：B
質問 # 45
NACE Level 1 Inspectors have been trained to perform:
- A. Visual inspection, Non-Destructive and Destructive testing
- B. Visual inspection only
- C. Visual inspection and Non-destructive testing
- D. All types of inspection
正解：C
質問 # 46
In a non-convertible coating the role of the primary solvent is to:
- A. To promote faster cure
- B. To dissolve the resin
- C. To make the coating flow out better
- D. To control the evaporation rate
正解：D
質問 # 47
......
合格させる保証付き無料クイズ2024年最新の実際に出ると確認されたNACE：https://jp.fast2test.com/NACE-CIP1-001-premium-file.html
無料CIP Level 1 NACE-CIP1-001究極の学習ガイド：https://drive.google.com/open?id=1mO_IuETAf9ovemWaimNpFnqiIaGzAAEV