2022年最新の有効なNACE-CIP2-001テスト解答とNACE試験PDF問題を試そう
無料NACE NACE-CIP2-001試験問題と解答トレーニングを提供していますFast2test
質問 15
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Exit the tank and immediately and report the problem to the nearest safety supervisor
- B. Don your air supplied respirator and continue the testing
- C. Exit the tank and document the incident in your daily report
- D. Investigate to find the source of the odor
正解: A
質問 16
The most likely area of failure on a buried external pipeline coating is the:
- A. Mainline coating
- B. Areas exposed to Ultra Violet light
- C. Field joint coating
- D. Ground bed
正解: C
質問 17
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. coatings are expected to degrade over time.
- B. linings protect the contents and the container.
- C. linings are more durable than coatings.
- D. coatings are more durable than linings.
正解: B
質問 18
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. Consensus
- B. De facto
- C. Mandatory
- D. Voluntary
正解: D
質問 19
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Advise the other inspector he is using an incorrect method
- B. Review the specification with the other inspector to see what method was specified
- C. Advise your QC Manager to change the ITP to the use of the salt smart meter
- D. Redo the pre-cleaning based on the other inspectors results
正解: B
質問 20
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
- B. Correct the errors yourself and suggest the Level 1 inspector be replaced
- C. Correct the errors yourself and submit the reports without any further action
- D. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
正解: A
質問 21
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Re-create the reports as not much was going on during night shift anyway
- B. Plainly state in your report that they are missing
- C. Do not complete your report until they can be found
- D. Use creative writing to cover over the fact they are missing
正解: B
質問 22
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Suggest to the Owner that the supervisor should be removed from site
- B. Defend the previous inspector
- C. Express a willingness to work with the site team and follow the specification
- D. Challenge the supervisor's authority
正解: C
質問 23
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of acid or caustic splashes
- B. Risk of chemical exposure
- C. a), b), and c)
- D. Risk of skin
正解: C
質問 24
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Require the Applicator to remove the coating
- B. Ignore the situation
- C. Stop the job
- D. Advise the Owner and write a Non-Conformance report
正解: A
質問 25
Which is used to calibrate a pH meter?
- A. Standard buffer solution
- B. Distilled water
- C. Standard solvent solution
- D. Deionized water
正解: A
質問 26
You can use magnifiers to examine all of the following EXCEPT
- A. Surface profile
- B. Blisters
- C. Mill scale
- D. Surface cleanliness
正解: D
質問 27
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method A - Cross Hatch
- B. Method A - X Cut
- C. Method B - X cut
- D. Method B - Cross Hatch
正解: B
質問 28
Coating Surveys are legally required:
- A. On food and beverage vessels and can linings
- B. On water tanks and potable water pipelines
- C. On high pressure gas lines and fireproofed structures
- D. On commercial marine vessels and offshore platforms
正解: D
質問 29
Corrosion is the reverse process of
- A. steel manufacturing.
- B. hot dipping.
- C. flaking.
- D. galvanic deterioration.
正解: A
質問 30
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Shut the job down
- B. Request that the Contractor re-blast the floor
- C. Call your supervisor
- D. Review the standard with the Contractor and re-inspect the floor
正解: D
質問 31
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. epoxies.
- B. urethanes.
- C. powder coatings.
- D. inorganic zincs.
正解: D
質問 32
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Check to See if the dehumidification equipment is operating correctly
- B. Document the readings at the end of the shift
- C. Call your supervisor
- D. Advise the coating applicator supervisor of your readings
正解: D
質問 33
When observing fabrication defects the NACE Inspector should:
- A. Stop the job immediately
- B. Write an NCR and call the fabricator
- C. Consult the specification to determine how they should be treated
- D. Require they be corrected prior to coating
正解: C
質問 34
......
トップクラスNACE NACE-CIP2-001オンライン問題集：https://jp.fast2test.com/NACE-CIP2-001-premium-file.html
NACE-CIP2-001練習問題集で検証済みのFast2test更新された100問題あります：https://drive.google.com/open?id=1qCJk8w32W1D8YJbUVoD39Fx4bzfmmVti