合格させるHPE Technical HPE0-S59テスト問題集で[2024年11月12日] 更新された81問あります
HP HPE0-S59実際の問題と100%カバー率でリアル試験問題
質問 # 19
What is one of me benefits of using HPE Composer 2?
- A. HPE Composer 2 has 128GB of memory and 4 AMD CPUs to improve performance of me management system
- B. A pair of HPE Composer 2 modules can manage 42 frames, compared to 21 frames managed by HPE Composer
- C. The administrator can access an HPE Synergy Composer 2 appliance remotely to perform First Time Setup
- D. HPE Composer 2 modules are required to manage HPE virtual Connect SE 100GD F32 Modules for Synergy
正解：A
質問 # 20
Your customer plans to setup an HPE Synergy solution based on SY480 Gen10 compute nodes with the following connectivity options - SAS connectivity installed in the first fabric - FC connectivity Installed In the second fabric - Ethernet connectivity installed in the third fabric.
Which statement regarding this setup is true?
- A. Each interconnect module in each fabric must be properly licensed in HPE OneView
- B. Compute nodes must have a second CPU installed to access the second fabric.
- C. Interconnect modules that provide SAS connectivity should be moved to the third fabric
- D. Each compute node must have at least 768GB of memory installed
正解：B
解説：
In HPE Synergy configurations, compute nodes must have a second CPU installed to access the second fabric.
This requirement is due to the architecture of the Synergy compute nodes, where the second CPU is necessary to enable the additional PCIe lanes required for connectivity to the second fabric.
質問 # 21
Your customer plans to add four HPE Synergy frames to an existing management ring Ail installed frames are equipped with two 2-port FLM modules, while new frames will be equipped with 4-port FLM modules.
Which statement about mixing different FLM modules is true?
- A. A management ring can contain mixed frame link module configurations
- B. A management ring with mixed FLM modules cannot have more than 12 frames
- C. Existing 2-port FLM modules must be replaced with 4-port FLM modules
- D. Mixing different FLM modules is allowed if all of them have the same firmware version
正解：B
質問 # 22
What is a restriction of using a RoCE network?
- A. it is not supported with HPE Virtual Connect SE 40 GD F8 Module for HPE Synergy.
- B. It does not support Private VLAN and Multicast VLAN.
- C. It is by default configured as an untagged network and cannot be a part of a network set.
- D. It does not support smart link and private network features.
正解：D
解説：
A restriction of using a RoCE (RDMA over Converged Ethernet) network is that it does not support smart link and private network features. These features are essential for certain network configurations and use cases, but they are not available in RoCE networks, which are designed for high-performance, low-latency communication.
質問 # 23
Which statement about the SY480 Gen10 Plus Compute Module is true?
- A. It cannot be mixed with Gen9 compute modules in the same frame.
- B. It only supports NVDIMM Persistent Memory.
- C. It supports "3rd Gen AMO EPYC Server Processors with 64 cores.
- D. It supports 8 memory channels and memory DIMMs of up to 256GB.
正解：D
解説：
The HPE Synergy 480 Gen10 Plus Compute Module supports 8 memory channels and can accommodate memory DIMMs of up to 256GB. This capability ensures high memory bandwidth and large memory capacity, which are essential for demanding workloads and applications.
質問 # 24
You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support Which interconnects are required to support this connection? (Select two.)
- A. HPE Virtual Connect SE 32Gb FC Module for HPE Synergy
- B. Brocade 16Gb Fibfe Channel SAN Switch Module for HPE Synergy
- C. Brocade 32Gb Fibre Channel SAN Switch Module for HPE Synergy
- D. HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy
- E. HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy
- F. HPE Virtual Connect SE 16Gb FC Module for HPE Synergy
正解：D、E
解説：
To configure a RoCE (RDMA over Converged Ethernet) network for HPE J2000 Flash Enclosure support, you need interconnects that support high-bandwidth, low-latency Ethernet connections. The HPE Virtual Connect SE 40Gb F8 Module and the HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy are suitable choices, as they provide the necessary capabilities for RoCE and lossless networking.
質問 # 25
Which compute node parameters are captured within server hardware type?
- A. installed operating system
- B. Size of the memory Installed
- C. Number of the CPUs
- D. Mezzanine card configuration
正解：D
解説：
The server hardware type in HPE OneView captures parameters such as the mezzanine card configuration.
This information is crucial for defining the connectivity and expansion capabilities of the compute node, ensuring that the appropriate resources are available for specific workloads.
質問 # 26
Which statement about HPE Superdome nPars is true?
- A. nPars are supported only with 3rd Generation Intel Xeon Scalable Processors
- B. Rack Management Controller is required Tor nPar configuration
- C. Chassis in the same nPar can have different memory configuration
- D. Chassis in the same nPar can have different CPU configuration
正解：B
解説：
The Rack Management Controller (RMC) is a critical component for configuring nPartitions (nPars) in HPE Superdome systems. The RMC provides the necessary control and management interfaces to define and manage nPars, ensuring proper allocation of resources and isolation of workloads.
質問 # 27
Which tool can be used to evaluate me health of an HPE Oneview appliance before proceeding with an appliance updated.
- A. HPE OneView Global Dashboard
- B. HPE OneView Update Readiness Checker
- C. HPE Composer Maintenance Console
- D. HPE OneView Firmware Compliance Report
正解：B
解説：
The HPE OneView Update Readiness Checker is a tool specifically designed to evaluate the health and readiness of an HPE OneView appliance before proceeding with an update. It checks for any potential issues that could affect the update process and provides recommendations for resolution.
質問 # 28
Your customer wants to compare HPE Superdome Flex with HPE Superdome Flex 280.
Which statement about these two systems is true?
- A. Only HPE Superdome Flex 280 can support multiple nPars
- B. Only HPE Superdome Flex supports 32 sockets and 48TB of memory
- C. Only HPE Superdome Rex 280 can be managed using HPE OneView
- D. Only HPE Superdome Flex supports HPE Persistent Memory
正解：B
解説：
The HPE Superdome Flex system supports configurations of up to 32 sockets and 48TB of memory, making it suitable for extremely large-scale and demanding workloads. In contrast, the HPE Superdome Flex 280 has a lower maximum configuration limit, making it more suited for smaller-scale deployments compared to the full Superdome Flex.
質問 # 29
Your customer has experience with utilization sampling for HPE Virtual Connect SE 100 Gb F32 Module for HPE Synergy. They have recently purchased HPE VC FC modules.
What must you be aware of regarding utilization sampling for the new modules?
- A. For HPE VC FC modules, utilization sampling is always enabled and cannot be disabled
- B. Utilization sampling for HPE VC FC modules must be enabled manually using CLI.
- C. Utilization sampling works the same way tor any type of HPE Synergy interconnect modules
- D. For HPE VC FC modules, utilization sampling can be enabled once appropriate license is applied
正解：A
解説：
For HPE Virtual Connect Fibre Channel (VC FC) modules, utilization sampling is always enabled by default and cannot be disabled. This feature ensures continuous monitoring of the module's performance and utilization, providing valuable insights for managing the Fibre Channel network.
質問 # 30
Which statement about an HPE Oneview support dump is true?
- A. Support dump is a binary file that can be opened only in a dedicated application
- B. Appliance support dump by default contains a logical enclosure support dump
- C. Preview support dump is available only when creating an appliance support dump
- D. Support dump can be created if HPE Virtual Connect modules are installed in the frame
正解：A
質問 # 31
The proposal consists of.
- 3 HPE Synergy 12000 frames
- 6 HPE Composer 2 modules
- 2 HPE Virtual Connect SE 100 GO F32 Module
- 4 HPE Synergy 50 GO interconnect Link Module
Which statements about this proposed design are true? (Select two.)
- A. The selected interconnect modules do not provide the requested WWN virtualization
- B. HPE Synergy 50Gb ILMs must be replaced with HPE Virtual Connect SE 100 GO F32 modules
- C. The current setup can support up to 18 HPE Synergy 480 Gen10 Plus compute modules
- D. FC upgrade licenses for HPE Virtual Connect SE 100 GbF32 Module must be added
- E. Remove 4 HPE Composer 2 modules from the design, as they are not required
正解：D、E
解説：
* D. FC upgrade licenses for HPE Virtual Connect SE 100 GbF32 Module must be added:To enable Fibre Channel functionality on the HPE Virtual Connect SE 100Gb F32 Modules, it is necessary to add FC upgrade licenses. These licenses unlock the FC capabilities required for the proposed setup.
* E. Remove 4 HPE Composer 2 modules from the design, as they are not required:The proposed design includes 6 HPE Composer 2 modules, but typically, only a pair of HPE Composer 2 modules is required to manage up to 21 frames. Therefore, the remaining 4 Composer 2 modules are not necessary and can be removed from the design.
質問 # 32
Your customer plans to deploy HPE OneView for VMware vCenter Server together with HPE Storage Integration Pack for VMware vCenter. The customer wants to use them to manage HPE Synergy Gen10 compute modules. HPE ProLiant Gen 10 servers and an MSA array.
Which statement about compatibility of the existing environment with the planned software components is true?
- A. Both HPE Synergy Gen10 full-height compute module plugins will require a license
- B. To use the required plugins HPE ProLiant Gen10 systems must be managed using HPE OneView
- C. HPE OneView for VMware vCenter Server does not support standalone HPE ProLiant servers
- D. HPE Storage integration Pack for VMware vCenter does not support MSA arrays
正解：D
解説：
The HPE Storage Integration Pack for VMware vCenter is designed to provide management capabilities for HPE storage arrays within the VMware vCenter environment. However, it does not support MSA arrays. This means that while you can manage HPE Synergy Gen10 compute modules and HPE ProLiant Gen10 servers, the MSA array will not be manageable through the HPE Storage Integration Pack.
質問 # 33
Which HPE Virtual Connect feature allows an administrator to suppress excessive inbound multicast broadcast and destination lookup failure (OLF) packets?
- A. Loop protection
- B. Pause flood protection
- C. LLDP tagging
- D. Storm control
正解：D
質問 # 34
Click the drop-down menu that will allow you to define the location of the master modules within the logical interconnect group.
正解：
解説：
質問 # 35
......
HP HPE0-S59試験の準備には、HPEはインストラクター主導のトレーニング、オンライントレーニング、自己ペーストレーニングを含むさまざまなトレーニングコースを提供しています。さらに、HPE Learning Centerでは、模擬試験、学習ガイド、その他のリソースを提供して、試験の準備をサポートします。
HP HPE0-S59リアル2024年最新のブレーン問題集で模擬試験問題集：https://jp.fast2test.com/HPE0-S59-premium-file.html
HPE0-S59無料試験問題と解答PDF更新されたのは2024年11月：https://drive.google.com/open?id=1DItkuvtrGcUkdMOEItG3aa97XE4Lrt6H