[2024年01月] 試験350-501最新ブレーン専門問題集はここ
無料で使える350-501試験問題集試験点数を伸ばそう
シスコ350-501認定を取得することは、ネットワーキング分野における専門知識を証明し、キャリアの見通しを向上させる素晴らしい方法です。世界中の雇用主から高く評価される認定であり、ネットワークエンジニア、ネットワーク管理者、ネットワークアーキテクトなど、さまざまな仕事の機会を確保するのに役立ちます。試験に合格して認定を取得することで、このダイナミックでエキサイティングな分野でスキルと知識をさらに発展させるためのさまざまな貴重なリソースやネットワーキングの機会にアクセスすることもできます。
質問 # 201
Refer to the exhibit.
A network engineer is configuring MPLS LDP synchronization on router R1. Which additional configuration must an engineer apply to R1 so that it will synchronize to OSPF process 1?
- A. Option C
- B. Option A
- C. Option B
- D. Option D
正解：B
質問 # 202
Refer to the exhibit:
R1 and R2 are directly connected with Fast Ethernet interfaces and have the above configuration applied OSPF adjacency is not formed. When the debug ip ospf hello command is issued on R1. these log messages are seen.
Which command can be configured on routers R1 and R2 on fO/O interfaces to form OSPF adjacency?
- A. ip ospf network point-to- multipoint non-broadcast
- B. ip ospf network point-to-point
- C. ip ospf network non-broadcast
- D. ip ospf network broadcast
正解：B
質問 # 203
Refer to the exhibit:
Which statement about the status of the neighbor relationship between R1 and R2 is true?
- A. The neighbor relationship is down because the two routers are in the same subnet.
- B. The neighbor relationship is down because the two routers are configured with different area types
- C. The neighbor relationship is down because R2 is operating as a Level 1 router and the two routers are in different area
- D. The neighbor relationship is up because R2 is level 1 and level 2 router.
正解：C
質問 # 204
Refer to the exhibit.
An engineer is configuring router R1 for OSPFv3 as shown. Which additional configuration must be performed so that the three active interfaces on the router will advertise routes and participate in OSPF IPv6 processes?
- A. to 2.2.2.2, with a TTL of 2 or more
- B. from 2.2.2.2, with a TTL of less than 2
- C. from 2.2.2.2, with a TTL of 253 or more
- D. to 2.2.2.2, with a TTL of less than 253
正解：B
質問 # 205
Refer to the exhibit:
Which statement about the status of the neighbor relationship between R1 and R2 is true?
- A. The neighbor relationship is down because the two routers are in the same subnet.
- B. The neighbor relationship is down because the two routers are configured with different area types
- C. The neighbor relationship is up because R2 is level 1 and level 2 router.
- D. The neighbor relationship is down because R2 is operating as a Level 1 router and the two routers are in different area
正解：A
質問 # 206
Refer to the exhibit. P3 and PE4 are at the edge of the service provider core and serve as ABR routers Aggregation areas are on either side of the core.
Which statement about the architecture is true?
- A. To support seamless MPLS, the BGP route reflector feature must be disabled
- B. If each area is running its own IGP. BGP must provide an end-to-end MPLS LSP
- C. If each area is running its own IGP. the ABR routers must redistribute the IGP routing table into BGP
- D. To support seamless MPLS. TDP must be used as the label protocol
正解：B
解説：
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9600/software/release/16-
12/configuration_guide/mpls/b_1612_mpls_9600_cg/configuring_seamless_mpls.html
質問 # 207
Refer to the exhibit.
Refer to the exhibit. LDP peering between routers R1 and R2 is dropped when the link between R1 and R2 is taken offline. However, LDP peering between R2 and R3 stays up when the link between R2 and R3 is taken offline. Which action allows MPLS traffic forwarding to continue normally if the link between R1 and R2 goes down?
- A. Enable IGP and LDP Synchronization on R2.
- B. Implement LDP Session Protection on R1.
- C. Implement LDP Session Protection on R2.
- D. Enable IGP and LDP Synchronization on R1.
正解：B
質問 # 208
Which statement about segment routing prefix segments is true?
- A. It requires using EIGRP to operate.
- B. It is the longest path to a node.
- C. It is linked to a prefix SID that is globally unique within segment routing domain.
- D. It is linked to an adjacency SID that is globally unique within the router.
正解：C
解説：
Section: MPLS and Segment Routing
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/segment-routing/configuration/ guide/b-seg-routing-cg-asr9k/b-seg-routing-cg-asr9k_chapter_010.pdf
質問 # 209
Reter to the exhibit. ISP A provides VPLS services and DDoS protection to Company XYZ to connect their branches across the North America and Europe regions. The uplink from the data center to the ISP is 100 Mbps. The Company XYZ security team asked the ISP to redirect ICMP echo requests, which are currently going to the web server, to a new local security appliance.
Which configuration must an ISP engineer apply to router R2 to redirect the ICMP traffic?
- A. class-map type traffic match-all B_210.10.65.1
match destination-address ipv4 210.10.65.1
match protocol 7
match ipv4 icmp-type 3 - B. class-map type traffic match-all B_210.10.65.1
match destination-address ipv4 210.10.65.1
match protocol 3
match ipv4 icmp-type 5 - C. class-map type traffic match-all B_210.10.65.1
match destination-address ipv4 210.10.65.1
match protocol 6
match ipv4 icmp-type 9 - D. class-map type traffic match-all B_210.10.65.1
match destination-address ipv4 210.10.65.1
match protocol 1
match ipv4 icmp-type 8
正解：D
質問 # 210
Refer to the exhibit.
An engineer is updating this network to meet these conditions:
* Area 10 will receive inter-area routes and support mutual redistribution of external routes with the extranet.
* The ::/0 route is prohibited in Area 10.
* Area 11 will receive only the ::/0 route from the ABR.
* External route redistribution is not supported in Area 11.
* The ABR in Area 11 will advertise no interarea routes.
Which two configurations must be performed to meet the requirements? (Choose two.)
- A. Configure area 11 as nssa no-summary on R7 and as nssa on XR31.
- B. Configure area 11 as stub no-summary on R7 and as stub on XR31.
- C. Configure area 10 as stub on R9 and XR32.
- D. Configure area 11 as nssa default-information-originate on R7 and as nssa on XR31.
- E. Configure area 10 as nssa on R9 and XR32.
正解：B、E
質問 # 211
Refer to the exhibit. An engineer configured multicast routing on client's network.
What is the effect of this multicast implementation?
- A. R1 floods information about R2 throughout the multicast domain.
- B. R2 is unable to share information because the ip pirn autorp listener command is missing.
- C. R2 is elected as the RP for this domain.
- D. R2 floods information about R1 throughout the multicast domain.
正解：B
質問 # 212
Refer to the exhibit:
Which command is used to complete this configuration for QoS class-based marking?
- A. PE-A(config-pmap-c)#random-detect
- B. PE-A(config -pmap-c)#priority
- C. PE-A(config-pmap-c)#fair-queue
- D. PE-A(config-pmap-c)#set dscp ef
正解：D
質問 # 213
Which service is a VNF role?
- A. Network
- B. Firewall
- C. Compute
- D. Storage
正解：B
質問 # 214
Refer to the exhibit. Router P4 and P5 receive the 0.0.0.0/0 route from the ISP via eBGP peering P4 is the primary Internet gateway router, and P5 is its Backup. P5 is already advertising a default route into OSPF domain. Which configuration must Be applied to P4 so that advertises a default route Into OSPF and Becomes me primary internet gateway for the network?
- A. Option A
- B. Option B
- C. Option C
- D. Option D
正解：C
質問 # 215 
Refer to the exhibit. This configuration is being applied on an IOS XR router.
Which statement about this configuration is true?
- A. It is used to create a streaming subscription with a 600-second interval.
- B. It is used to enable gRPC.
- C. It is used to create a streaming subscription with a 60-Second interval.
- D. It is used to set up configuration to poll network data.
正解：C
解説：
Section: Automation and Assurance
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/telemetry/b-telemetry-cg-asr9000-
62x/b-telemetry-config-guide-asr9000_chapter_01.html
質問 # 216
Refer to the exhibit:
What does this value mean when it is received in XML?
- A. It indicates a break in a sequence
- B. It shows the ending of the script
- C. It indicates a value assigned by a network administrator to tag a route
- D. It means a data field is blank
正解：D
質問 # 217
An engineer is moving all of an organization's Cisco IOS XE BGP routers to the address-family identifier format. Which command should be used to perform this upgrade quickly with the minimum service disruption?
- A. ip bgp-community new-format
- B. address-family ipv4
- C. bgp upgrade-cli
- D. vrf upgrade-cli
正解：C
質問 # 218
A network engineer must configure a router for Flexible NetFlow IPFIX export. The IP address of the destination server is 172.17.12.1. The source address must be set to the Loopback0 IPv4 address and exported packets must be set to DSCP CS3. The TTL must be 64 and the transport protocol must be set to UDP with destination port 4739. Which configuration must the engineer apply to the router?
- A. configure terminal
flow exporter EXPORTER-1
destination 172.17.12.1
source Loopback0
dscp 24
ttl 64
export-protocol netflow-v9
transport udp 4739
end - B. configure terminal
flow exporter EXPORTER-1
destination 172.17.12.1
source Loopback0
dscp 24
ttl 64
export-protocol ipfix
end - C. configure terminal
flow exporter EXPORTER-1
destination 172.17.12.1
source Loopback0
dscp 3
ttl 64
export-protocol ipfix
end - D. configure terminal
flow exporter EXPORTER-1
destination 172.17.12.1
source Loopback0
dscp 3
ttl 64
export-protocol netflow-v9
transport udp 4739
end
正解：B
質問 # 219
Refer to the exhibit.
A network engineer must meet these requirements to provide a connects, solution:
The customer connected to Area 2 needs to access the application in Area 1 on the 10.10.10.0/24 subnet The Customer must not have access to the 20.10 30.0/24 subnet.
The service provider must make sure that the Area 2 routing database limits the number of IP addresses in the routing table Which two configurations must be implemented to meet the requirements? (Choose two)
- A. Set a tag value of 200 to match the summary address 10.0.0/16 on R2.
- B. Set a tag value of 200 to match the summary address 10.0.0./16 on R1.
- C. Set a tag value of 200 to match the summary address 10.0.0.0/16 on R3.
- D. Apply the route map for tag 200 and leak Level 2 routes into Level 1 Area 2 on R3
- E. Apply the route map for tag 200 and teak Level 2 routes into Level 1 Area 2 on R4.
正解：C、D
質問 # 220
......
心強い350-501のPDF問題集は350-501問題：https://jp.fast2test.com/350-501-premium-file.html
2024年最新の実際に出る350-501問題集には試験のコツがあるPDF試験材料：https://drive.google.com/open?id=1RVCtHyhvYqx9zQawGv8Ut7gI_7-0tKWZ