[2023年10月] 確実合格する有効な方法Network Appliance試験問題集でNS0-184試験学習ガイド
NS0-184問題集とNetApp Certified Storage Installation Engineer, ONTAPトレーニングコースでお客様の合格を楽にさせる学習合格試験問題！
Network Appliance NS0-184（NetApp認定ストレージインストールエンジニア、ONTAP）認定試験は、NetAppストレージソリューションと仕事をするストレージインストールエンジニアのスキルと知識を正当化するためのグローバルな認定試験です。この認定試験は、インストール、構成、トラブルシューティング、データ管理のベストプラクティスなど、幅広いトピックをカバーしています。NS0-184認定試験に合格することは、NetApp認定ストレージインストールエンジニアとしての必須のステップであり、キャリアを進めるための重要な一歩です。
NS0-184試験では、ハードウェアやソフトウェアコンポーネントを含むNetApp ONTAPシステムをインストールおよび構成する候補者の能力と、基本的なトラブルシューティングタスクを実行する機能をテストします。この試験では、データ保護、高可用性、ストレージ効率などのトピックもカバーしています。これらは、ストレージインストールエンジニアにとって不可欠なスキルです。 NS0-184試験に合格すると、候補者がNetApp ONTAPストレージシステムを効果的に展開および管理するために必要なスキルと知識を持っていることが示されています。
質問 # 19
Your customer is migrating data from a legacy FAS8020 system that runs ONTAP 9.5 software to a new AFF A250 MetroCluster over IP configuration.
In this scenario, which two methods would be supported to migrate the data? (Choose two.)
- A. Perform a controller swap from the FAS8020 to the AFF A250s.
- B. Configure a SnapMirror copy between the FAS8020 and the AFF A250 systems.
- C. Use a host-based copy migration method.
- D. Create a 4-node cluster on one side and use the vol move command to migrate the data.
正解：A、B
質問 # 20
Click the Exhibit button.
You want to add a FAS2750 HA pair to an existing 6-node cluster.
Referring to the exhibit, which action would you perform to begin adding the node?
- A. Use the back command to begin the Cluster Setup wizard.
- B. Use the node setup wizard and select 0a as the management interface.
- C. Use the exit or quit commands then run the cluster setup command.
- D. Reboot the node and enter maintenance mode and run the Cluster Setup wizard.
正解：B
質問 # 21
You are preparing to physically install a new AFF A400 cluster into a customer's racks. All equipment has been delivered to the customer's site.
Which three tools do you need to complete this installation? (Choose three.)
- A. Phillips #2 screwdriver
- B. cable management tray
- C. laptop computer
- D. slide rail kit
- E. additional network cables
正解：A、C、E
質問 # 22
You are installing a new AFF A400 cluster and need to access the cluster management LIF from a remote subnet with the fully qualified domain name (FQDN) a400.lab.netapp.com.
In this scenario, which two network components must be configured to log in to ONTAP System Manager from the remote subnet? (Choose two.)
- A. route
- B. VLAN
- C. NTP
- D. DNS
正解：A、D
質問 # 23
Click the Exhibit button.
You plan to install a new ONTAP cluster at a customer site by using the new ONTAP System Manager 9.7 GUI.
Referring to the exhibit, what must you do before you provision initial storage?
- A. Configure cluster LIFs.
- B. Configure protocols.
- C. Configure aggregates.
- D. Configure a remote tier.
正解：C
質問 # 24
After adding two nodes to an FC-enabled cluster, the storage administrator wants to ensure that existing LUNs can use paths on the new nodes.
What is required to complete this task?
- A. Use the lun bind create command.
- B. Use the lun mapping add-reporting-nodes command.
- C. Rescan the bus on the hosts by using the rescan-scsi-bus.sh script.
- D. Use the storage port rescan command.
正解：B、D
質問 # 25
Click the Exhibit button.
You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.
For a high availability, which ports should swap Ethernet cables?
- A. Swap node2:e4a and node2:e8a.
- B. Swap node1:e4a and node1:e8a.
- C. Swap node1:e8a and node2:e4a.
- D. Swap node1:e4a and node2:e4b.
正解：A
質問 # 26
Before installing an 8-node cluster for a customer, you want to validate compatibility with existing hardware.
Which two tools would you use to validate the configuration? (Choose two.)
- A. Active IQ Config Advisor
- B. Interoperability Matrix Tool
- C. Hardware Universe
- D. Active IQ System Manager
正解：A、B
質問 # 27
You want to use the NetAppDocs tool to collect information on a newly configured ONTAP 9.8 cluster and to generate a Word document with the details of the cluster configuration.
Which two data sources would you use to collect the necessary data? (Choose two.)
- A. ONTAP Cluster
- B. Active IQ Digital Advisor
- C. AutoSupport packages
- D. Active IQ Unified Manager
正解：A、D
質問 # 28
What are two ONTAP storage efficiency technologies that would be used on an AFF A400 cluster? (Choose two.)
- A. thin provisioning
- B. FlashCache
- C. FlexClone volumes
- D. Flash Pool
正解：B、D
質問 # 29
What should you do to change the data protocol of a LIF?
- A. Shut down the assigned port.
- B. Add the new data protocol to the LIF.
- C. Delete and re-recreate the LIF.
- D. Put the LIF in another broadcast domain.
正解：C
質問 # 30
You are preparing for the installation of a new 2-node switchless AFF A250 ONTAP 9.8 cluster and need to obtain the preinstallation information from the customer.
In this scenario, what are three examples of data required from the customer? (Choose three.)
- A. management IP addresses
- B. BMC IP addresses
- C. cluster name
- D. cluster switch name
- E. gateway IP address
正解：A、B、D
質問 # 31
You are installing an AFF A700 system with two disk shelves using ADPv2. After setting up the cluster, you realize that one drive shelf was powered off and that the drives have not been assigned to any of the nodes.
In this scenario, which two resources will help you find a solution? (Choose two.)
- A. Active IQ Config Advisor
- B. Active IQ Digital Advisor
- C. NetApp Documentation Center
- D. NetApp Knowledge Base
正解：A、D
質問 # 32
After the Installation of a new NetApp FAS system, you use theNetAppDocs tool for site design documentation.
In this scenario, in which three document formats would you create an inventory report? (Choose three.)
- A. .pdf
- B. .xlsx
- C. .ps
- D. .html
- E. .docx
正解：A、D、E
質問 # 33
After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.
In this scenario, which two commands would you use to accomplish this task? (Choose two.)
- A. system node autosupport invoke
- B. system node autosupport destination show
- C. system node autosupport check show
- D. system node autosupport history show
正解：C、D
質問 # 34
When creating a new 3.8 TB SSD-based aggregate, what is the default RAID type used with ONTAP 9.8?
- A. RAID 0
- B. RAID-TEC
- C. RAID 4
- D. RAID DP
正解：D
質問 # 35
You completed a 2-node AFF A700 installation according to the poster. You run the disk show -fields owner command and notice that all drives are assigned to node 1.
In this scenario, which tool would you use to access documentation and guidelines to solve the issue?
- A. Active IQ One Collect
- B. NetAppDocs
- C. NET2
- D. Active IQ Unified Manager
正解：B
質問 # 36
What is the default shelf ID for disk shelves with IOM12 modules?
- A. 0
- B. 01
- C. 1
- D. 00
正解：D
質問 # 37
......
リアル試験問題と解答Network Appliance NS0-184問題集はここに：https://drive.google.com/open?id=1ems23gcX2lLgKnYMOjHRhqNXMSku3Xnb
最新 [2023年10月] 効果的な学習法で試験合格できるNS0-184：https://jp.fast2test.com/NS0-184-premium-file.html