[2023年04月30日] 300-615テストエンジンお試しセット、300-615問題集PDF [Q88-Q103]

[2023年04月30日] 300-615テストエンジンお試しセット、300-615問題集PDF

最新のCisco 300-615のPDFと問題集で（2023）無料試験問題解答

質問 # 88
Refer to the exhibit.

Refer to the exhibit. A network engineer is configuring the FCoE N_Port virtualization storage area network. After the initial implementation, server 11 fails to connect to the disk array. Which action resolves the issue?

A. On N9K interface vfc11, change switchport mode configuration to NP
B. On MDS interface vfc 1/1, change switchport mode configuration to VF
C. On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to E
D. On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to F

正解：C

質問 # 89
Refer to the exhibit.

A PC belongs to VLAN 68 The user experiences a large amount of packet loss when communicating with hosts that are outside of VLAN 68. Which action resolves the problem?

A. Enable the peer-gateway feature
B. Remove the HSRP configuration
C. Configure ip arp synchronization on both switches.
D. Replace HSRP with GLBP

正解：A

解説：
Explanation
I assume that the PC is sending traffic with destination MAC of Nexus physical interfaces. If more snap shots about this question are available, please share.

質問 # 90
Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.

正解：

解説：

質問 # 91
Refer to the exhibit.

An attempt to bind the Ethernet interface to vFC fails. Which action resolves the issue?

A. Configure the FCoE VLAN that corresponds to the vFC VSAN as a private VLAN.
B. Configure the interface as a trunk port.
C. Configure the interface to use the native VLAN of the trunk port.
D. Add the FCoE VLAN to the allowed VLAN list.

正解：B

質問 # 92
An engineer removes a VMM domain from an endpoint group called EPG-1, but the distributed port group fails to be deleted. Which action must be taken to resolve the issue?

A. Remove the port group manually.
B. Migrate all virtual machines in the EPG-1 to different port groups.
C. Migrate all virtual machines in the EPG-1 to different hypervisors.
D. Remove the remaining EPGs from the VMM domain.

正解：B

質問 # 93
After upgrading a client's fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)

A. Admin page, PollInternalBackup stage
B. Service profiles page, InternalBackup stage
C. Equipment FSM page, InternalBackup stage
D. Equipment FSM page, PollInternalBackup stage
E. Admin page, InternalBackup stage.

正解：A、C

解説：
Section: Management and Operations
Explanation/Reference:

質問 # 94
During a boot process of a Cisco UCS C-Series Rack Server, an engineer receives a "No Signal" message from the vKVM and physical connection. Which set of steps resolves the issue?

A. 1- Power off the server and disconnect the power cord
2- Confirm that all cards are available
3- Connect the power cord and power on the server
B. 1- Disconnect the power cord
2- Confirm that all cards are properly seated
3- Connect the power cord
C. 1- Power off the server and disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server
D. 1- Disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server

正解：C

解説：
Explanation
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/ts/guide/b_C-Series_Troubleshooting_Guide.pd

質問 # 95
An engineer configures FCoE between a set of ESXi hosts and a Cisco Nexus 5000 Series Switch. The Converged Network Adapter of the host fails to receive the response from the Cisco Nexus device. Also, the VFC interface is in a down state and the FIP adapter fails to receive 802.1q tagged frames. The host interface is configured for VLAN trunking. Which action resolves the issue?

A. Set the bound Ethernet trunk interface to non-FCoE native VLAN
B. Enable the active STP port state on the bound Ethernet interface
C. Activate the reception of Xoff pause frames from the server
D. Configure the UF link as a spanning-tree edge port

正解：D

質問 # 96
A server fails to boot from the operating system after a RAID1 cluster migration. The RAID remains in an inactive state during and after a service profile association. Which action resolves the issue?

A. Remove the local disk configuration policy.
B. Use a predefined local disk configuration policy.
C. Configure the SAN boot target to any configuration mode.
D. Configure the SAN boot target in the service profile.

正解：B

質問 # 97
A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image. Drag and drop the recovery steps from the left onto the correct order on the right.

正解：

解説：

質問 # 98
An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a "resolve slot" warning. Which server maintenance action resolves the issue?

A. Perform diagnostic interrupt on the server.
B. Decomission the server.
C. Re-acknowlegement the server.
D. Reset the server.

正解：C

解説：
Section: Compute Platforms

質問 # 99
Refer to the exhibit.

An engineer must save the running configuration to startup-config and generate a syslog message indicating that the configuration was modified, but an error was received. Which action resolves the issue?

A. Add event-default as a second action of the EEM script.
B. Use the extended command copy running-config startup-config.
C. Change the syslog action number to 1.
D. Save the configuration using a user with network-admin role.

正解：A

質問 # 100
An engineer is troubleshooting a custom AV pair that was created by a client on an external authentication server to map a read-only role for a specific security domain. Which AV pair solves the problem?

A. shell:domains=Security_Domain_1/Write_Role_1|Read_Role_2
B. shell:domains=Security_Domain_1//Read_Role_1|Read_Role_2
C. shell=Security_Domain_1/Read_Role_1|Read_Role_2
D. shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2

正解：D

質問 # 101

Refer to the exhibit. An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?

A. Integrate Cisco MDS with Microsoft Active Directory.
B. Include specific users into MDS role configuration.
C. Configure the role name to match the group name on Microsoft Active Directory.
D. Configure SSH logins on Cisco MDS switch.

正解：C

解説：
Section: Storage Network
Explanation

質問 # 102
Drag each item listed on the left to its proper category on the right Not all items will fit the categories.