2023年最新の更新のNSE 7 Network Security Architectが有効なNSE7_SDW-6.4問題集を無料提供しています
最新のFast2test NSE7_SDW-6.4PDF問題集をダウンロードしちゃおう：https://jp.fast2test.com/NSE7_SDW-6.4-premium-file.html（82問題と解答)
Fortinet NSE7_SDW-6.4は、ソフトウェア定義型広域ネットワーク（SD-WAN）の技術分野における個人の知識とスキルをテストするための試験です。この試験は、ネットワークセキュリティの専門家のスキルと知識を検証する包括的なセットであるFortinet Network Security Expert（NSE）認定プログラムの一部です。
Fortinet NSE7_SDW-6.4（Fortinet NSE 7-SD-WAN 6.4）認定試験は、有名なサイバーセキュリティソリューションプロバイダーであるFortinetが提供する専門レベルの認定です。この認定は、SD-WANソリューションの展開と管理の経験がある専門家向けに設計されています。この試験では、Fortinet Secure SD-Wanソリューションの実装、構成、およびトラブルシューティングにおける候補者の知識とスキルを検証します。
質問 # 30
Refer to the exhibit.
Which two statements about the IPsec VPN configuration and the status of the IPsec VPN tunnel are true? (Choose two.)
- A. FortiGate creates a single IPsec virtual interface that is shared by all clients.
- B. FortiGate maps the remote gateway 100.64.3.1 to tunnel index interface 1.
- C. FortiGate does not install IPsec static routes for remote protected networks in the routing table.
- D. FortiGate creates separate virtual interfaces for each dial-up client.
正解：A、B
解説：
If net-device is disabled, FortiGate creates a single IPSEC virtual interface that is shared by all IPSEC clients connecting to the same dialup VPN. In this case, the tunnel-search setting determines how FortiGate learns the network behind each remote client.
質問 # 31
Refer to the exhibit.
Which two statements about the debug output are correct? (Choose two )
- A. This traffic shaper drops traffic that exceeds the set limits.
- B. The debug output shows per-IP shaper values and real-time readings.
- C. FortiGate provides statistics and reading based on historical traffic logs.
- D. Traffic being controlled by the traffic shaper is under 1 Kbps.
正解：A、B
質問 # 32
Refer to the exhibit.
Based on the output shown in the exhibit, which two criteria on the SD-WAN member configuration can be used to select an outgoing interface in an SD-WAN rule? (Choose two.)
- A. Set cost 15.
- B. Set source 100.64.1.1.
- C. Set priority 10.
- D. Set load-balance-mode source-ip-ip-based.
正解：B
質問 # 33
Refer to the exhibits.
ExhibitA shows the system interface with the static routes and exhibit B shows the firewall policies on the managed FortiGate.
Based on the FortiGate configuration shown in the exhibits, what issue might you encounter when creating an SD-WAN zone for port1 and port2?
- A. port1 and port2 are not administratively down.
- B. port1 is referenced in a firewall policy.
- C. port1 is assigned a manual IP address.
- D. port2 is referenced in a static route.
正解：B
質問 # 34
Refer to the exhibit.
Which statement about the trace evaluation by FortiGate is true?
- A. Packets exceeding the configured maximum concurrent connection limit are denied by the per-IP shaper.
- B. The packet exceeded the configured bandwidth and was dropped based on the priority configuration.
- C. The packet exceeded the configured maximum bandwidth and was dropped by the shared shaper.
- D. Packets exceeding the configured concurrent connection limit are dropped based on the priority
正解：A
解説：
configuration.
Explanation:
SD-WAN 6.4.5 Study Guide. pg 137
質問 # 35
Refer to exhibits.
Exhibit A shows the SD-WAN rules and exhibit B shows the traffic logs. The SD-WAN traffic logs reflect how FortiGate processed traffic.
Which two statements about how the configured SD-WAN rules are processing traffic are true? (Choose two.)
- A. The initial session of an application goes through a learning phase in order to apply the correct rule.
- B. The implicit rule overrides all other rules because parameters widely cover sources and destinations.
- C. SD-WAN rules are evaluated in the same way as firewall policies: from top to bottom.
- D. The All_Access_Rules rule load balances Vimeo application traffic among SD-WAN member interfaces.
正解：A、C
質問 # 36
Refer to the exhibit. Which conclusion about the packet debug flow output is correct?
- A. The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the firewall policy, and the packet was dropped.
- B. The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.
- C. The total number of daily sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.
- D. The packet size exceeded the outgoing interface MTU.
正解：B
質問 # 37
Refer to the exhibit.
Based on the output shown in the exhibit, which two criteria on the SD-WAN member configuration can be used to select an outgoing interface in an SD-WAN rule? (Choose two.)
- A. Set cost 15.
- B. Set priority 10.
- C. Set load-balance-mode source-ip-ip-based.
- D. Set source 100.64.1.1.
正解：A、B
質問 # 38
Refer to the exhibit.
Which statement about the command route-tag in the SD-WAN rule is true?
- A. It enables the SD-WAN rule to load balance and assign traffic with a route tag
- B. It tags each route and references the tag in the routing table.
- C. It uses route tags for a BGP community and assigns the SD-WAN rules with same tag.
- D. It ensures route tags match the SD-WAN rule based on the rule order
正解：D
質問 # 39
In which two ways does FortiGate learn the FortiManager IP address or FQDN for zero-touch provisioning? (Choose two.)
- A. From a DHCP server configured with options 240 or 241
- B. From a FortiGuard definitions update
- C. From the central management configuration configured in FortiDeploy
- D. From another FortiGate device in the same local network
正解：A、C
解説：
https://www.historiantech.com/zeroish-touch-provisioning-with-fortimanager-explained/
質問 # 40
Which two interfaces are considered overlay links? (Choose two.)
- A. IPsec
- B. Physical
- C. GRE
- D. LAG
正解：A、C
質問 # 41
Refer to exhibits.
Exhibit A shows the firewall policy and exhibit B shows the traffic shaping policy.
The traffic shaping policy is being applied to all outbound traffic; however, inbound traffic is not being evaluated by the shaping policy.
Based on the exhibits, what configuration change must be made in which policy so that traffic shaping can be applied to inbound traffic?
- A. In the firewall policy, select Proxy-based as Inspection Mode.
- B. In the traffic shaping policy, select Assign Shaping Class ID as Action.
- C. Create a new firewall policy, and the select the SD-WAN zone as Incoming Interface.
- D. In the traffic shaping policy, enable Reverse shaper, and then select the traffic shaper to use.
正解：D
質問 # 42
Which action FortiGate performs on traffic that is subject to a per-IP traffic shaper of 10 Mbps?
- A. FortiGate guarantees a minimum of 10 Mbps of bandwidth to each source IP address.
- B. FortiGate limits each source IP address to a maximum bandwidth of 10 Mbps.
- C. FortiGate shares 10 Mbps of bandwidth equally among all source IP addresses.
- D. FortiGate applies traffic shaping to the original traffic direction only.
正解：B
質問 # 43
Refer to exhibits.
Exhibit A shows the source NAT global setting and exhibit B shows the routing table on FortiGate.
Based on the exhibits, which two statements about increasing the port2 interface priority to 20 are true? (Choose two.)
- A. All the existing sessions using SNAT will be flushed and routed through port1.
- B. All the existing sessions will continue to use port2, and new sessions will use port1.
- C. All the existing sessions that do not use SNAT will be flushed and routed through port1.
- D. All the existing sessions will be blocked from using port1 and port2.
正解：A、B
質問 # 44
Refer to exhibits.
Exhibit A.
Exhibit B.
Exhibit A shows the traffic shaping policy and exhibit B show: the firewall policy FortiGate is not performing traffic shaping as expected basi on the policies shown in the exhibits.
To correct this traffic shaping issue on FortiGate, what configuration change must be made on which policy?
- A. The URL category must be specified on the traffic shaping policy
- B. The web filter profile must be enabled on the firewall policy
- C. The shaper mode must be applied per-IP shaper on the traffic shaping policy
- D. The application control profile must be enabled on the firewall policy.
正解：B
質問 # 45
Refer to exhibits.
Exhibit A shows the SD-WAN rules and exhibit B shows the traffic logs. The SD-WAN traffic logs reflect how FortiGate processed traffic.
Which two statements about how the configured SD-WAN rules are processing traffic are true? (Choose two.)
- A. SD-WAN rules are evaluated in the same way as firewall policies: from top to bottom.
- B. The implicit rule overrides all other rules because parameters widely cover sources and destinations.
- C. The initial session of an application goes through a learning phase in order to apply the correct rule.
- D. The All_Access_Rules rule load balances Vimeo application traffic among SD-WAN member interfaces.
正解：A、B
質問 # 46
Refer to exhibits.
Exhibit A.
Exhibit B.
Exhibit A shows the traffic shaping policy and exhibit B show: the firewall policy FortiGate is not performing traffic shaping as expected basi on the policies shown in the exhibits.
To correct this traffic shaping issue on FortiGate, what configuration change must be made on which policy?
- A. The URL category must be specified on the traffic shaping policy
- B. The web filter profile must be enabled on the firewall policy
- C. The shaper mode must be applied per-IP shaper on the traffic shaping policy
- D. The application control profile must be enabled on the firewall policy.
正解：B
解説：
SD-WAN_6.4_Study_Guide page 131
質問 # 47
Which statement is correct about the SD-WAN and ADVPN?
- A. ADVPN interface can be a member of SD-WAN interface.
- B. Hub FortiGate is limited to use ADVPN as SD-WAN member interface.
- C. Spoke support dynamic VPN as a static interface.
- D. Dynamic VPN is not supported as an SD-Wan interface.
正解：D
質問 # 48
Refer to exhibits.
Exhibit A.
Exhibit B.
Exhibit A, which shows the SD-WAN performance SLA and exhibit B shows the health of the participating SD-WAN members.
Based on the exhibits, which statement is correct?
- A. The dead member interface stays unavailable until an administrator manually brings the interface back.
- B. The SLA state of port2 has exceeded three consecutive unanswered requests from the SLA server.
- C. Check interval is the time to wait before a packet sent by a member interface considered as lost.
- D. Port2 needs to wait 500 milliseconds to change the status from alive to dead.
正解：B
質問 # 49
Refer to the exhibit.
FortiGate has multiple dial-up VPN interfaces incoming on port1 that match only FIRST_VPN.
Which two configuration changes must be made to both IPsec VPN interfaces to allow incoming connections to match all possible IPsec dial-up interfaces? (Choose two.)
- A. Use unique Diffie Hellman groups on each VPN interface.
- B. Specify a unique peer ID for each dial-up VPN interface.
- C. Use different proposals are used between the interfaces.
- D. Configure the IKE mode to be aggressive mode.
正解：B、D
質問 # 50
Refer to the exhibit
Based on the exhibit, which two statements about existing sessions on FortiGate after a firewall policy change, are true?(Choose two.)
- A. Existing sessions remain unchanged after a policy change
- B. FortiGate re-evaluates new packets after a policy change
- C. All sessions are flushed by FortiGate after a policy change
- D. The old sessions terminate after a policy change
正解：A、B
質問 # 51
What are two roles that SD-WAN orchestrator plays when it works with FortiManager? (Choose two )
- A. It acts as a standalone device to assist FortiManager to manage SD-WAN interfaces on the managed FortiGate devices.
- B. It configures and monitors SD-WAN networks on FortiGate devices that are managed by FortiManager.
- C. It acts as a hub FortiGate with an SD-WAN interface enabled and managed along with other FortiGate devices by FortiManager.
- D. It acts as an application that is released and signed by Fortinet to run as a part of management extensions on FortiManager.
正解：B、D
解説：
SD-WAN 6.4 Guide Page 158.
質問 # 52
Refer to exhibits.
Exhibit A shows the firewall policy and exhibit B shows the traffic shaping policy.
The traffic shaping policy is being applied to all outbound traffic; however, inbound traffic is not being evaluated by the shaping policy.
Based on the exhibits, what configuration change must be made in which policy so that traffic shaping can be applied to inbound traffic?
- A. The reverse shaper option must be enabled and a traffic shaper must be selected
- B. A new firewall policy must be created and SD-WAN must be selected as the incoming interface.
- C. The guaranteed-10mbps option must be selected as the per-IP shaper option
- D. The guaranteed-10mbps option must be selected as the reverse shaper option.
正解：A
質問 # 53
......
Fortinet NSE7_SDW-6.4認定試験は、SD-WANに関連する様々なトピックをカバーしており、SD-WANアーキテクチャ、展開シナリオ、セキュリティ機能、管理ツールなどが含まれます。合格した候補者は、FortinetのSecure SD-WANソリューションについて、SSL検査、アプリケーション制御、侵入防止システム（IPS）などの高度なセキュリティ機能を含めた深い理解を持っています。また、SD-WANポリシー、ルーティングプロトコル、品質サービス（QoS）設定の構成と管理もできます。認定試験は、多肢選択問題と実践的なシナリオから構成されており、試験に合格するには70％以上のスコアが必要です。
実験された試験材料はNSE7_SDW-6.4：https://jp.fast2test.com/NSE7_SDW-6.4-premium-file.html
最新NSE7_SDW-6.4リアル試験問題をフォローせよ！：https://drive.google.com/open?id=1z_p2PV6tpBWEgSx4RIn_GECgHHz_VIrM