合格目指せ300-410試験最新の300-410試験問題集PDF 2023年更新
300-410試験問題集、365日更新無料サンプル
質問 # 20
What does IPv6 Source Guard utilize to determine if IPv6 source addresses should be forwarded?
- A. ACLS
- B. Binding Table
- C. DHCP
- D. ACE
正解：B
解説：
質問 # 21
Which router attaches the VPN label to incoming packets from CE routing?
- A. core router
- B. CE router
- C. PE router
- D. P router
正解：C
質問 # 22
An engineer configured policy-based routing for a destination IP address that does not exist in the routing table. How is the packet treated through the policy for configuring the set ip default next-hop command?
- A. Packets are forwarded to the specific next hop.
- B. Packets are forwarded based on the routing table.
- C. Packets are forwarded based on a static route.
- D. Packets are not forwarded to the specific next hop.
正解：A
質問 # 23
Refer to the exhibit.
The Customer Edge router (AS 65500) wants to use ASC100 as the preferred ISP for all external routes.
This configuration failed to send routes to AS 100 as the preferred path. Which set of configuration resolves the issue?
- A. Option A
- B. Option B
- C. Option C
- D. Option D
正解：B
質問 # 24
Refer to the exhibit.
After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1. Which action can the engineer take to solve the issue so that all the PCs are reachable?
- A. Set the administrative distance 100 under the RIP process on R2.
- B. Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.
- C. Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.
- D. Redistribute the directly connected interfaces on R2.
正解：B
質問 # 25
Refer to the exhibit.
Although summarization is configured for R1 to receive 10.0.0.0/8. more specific routes are received by R1.
How should the 10.0.0.0/8 summary route be received from the neighbor, attached to R1 via Fast Ethernet0/0 interface?
- A. The summarization condition is not met. The network 10.1.100.0/24 should be changed to
172.16.0.0/24. - B. R1 should configure the ip summary-address eigrp <AS number> 10.0.0.0 0.0.0.255 command under the Fast Ethernet 0/0 interface.
- C. The summarization condition is not met Router 10 1 100.10 requires a route for 10 0.0.0/8 that points to null 0
- D. R1 should configure the ip summary-address eigrp <AS number> 10.0.0.0.255.0.0.0 command under the Fast Ethernet 0/0 interface.
正解：B
質問 # 26
Refer to the Exhibit.
R1 and R2 use IGP protocol to route traffic between AS 100 and AS 200 despite being configured to use BGP. Which action resolves the issue and ensures the use of BGP?
- A. Remove distance commands under BGP AS 100 and AS 200.
- B. Configure distance to 100 under the EIGRP process of R1 and R2.
- C. Configure distance to 100 under the OSPF process of R1 and R2
- D. Remove distance commands under BGP AS 100.
正解：A
質問 # 27
Refer to the exhibit.
An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+. Which action produces the desired configuration?
- A. Add the aaa authentication login default none command to the global configuration.
- B. Add the aaa authentication login default group tacacs+ local-case command to the global configuration.
- C. Replace the capital "C" with a lowercase "c" in the aaa authentication login Console local command.
- D. Add the login authentication Console command to the line configuration
正解：D
解説：
Reference:
https://community.cisco.com/t5/switching/how-to-define-login-local-for-console-0/td-p/2949493
質問 # 28 
Refer to the exhibit. A network administrator redistributed the default static route into OSPF toward all internal routers to reach to Internet. Which set of commands restores reachability to the Internet by internal routers?
- A. router ospf 1
redistribute connected 0.0.0.0 - B. router ospf 1
default-information originate - C. router ospf 1
redistribute static subnets - D. router ospf 1
network 0.0.0.0 0.0.0.0 area 0
正解：B
質問 # 29
Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.
正解：
解説：
質問 # 30
Refer to the exhibit.
An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries. Which action ensures consistency between the two times?
- A. Make sure that the clock on the device is synchronized with an NTP server.
- B. Configure the service timestamps log datetime localtime command in global configuration mode.
- C. Configure the service timestamps log uptime command in global configuration mode.
- D. Configure the logging clock synchronize command in global configuration mode.
正解：B
解説：
Explanation
https://www.cisco.com/c/en/us/td/docs/routers/xr12000/software/xr12k_r3-9/system_management/command/refe By default, syslog and debug messages are stamped by UTC, regardless of the time zone that device configured. You should append localtime key word to "service timestamp {log | debug} datetime msec" global command to change that behavior.
https://community.cisco.com/t5/networking-documents/router-log-timestamp-entries-are-different-from-the-syste
https://www.cisco.com/E-Learning/bulk/public/tac/cim/cib/using_cisco_ios_software/cmdrefs/service_timestamp
質問 # 31
Drag and drop the ICMPv6 neighbor discovery messages from the left onto the correct packet types on the right.
正解：
解説：
Explanation
Table Description automatically generated with medium confidence
質問 # 32
Refer to the exhibit.
Which configuration enables OSPF for area 0 interfaces to adjacency with a neighboring router with the same VRF?
- A. router ospf 1
interface Ethernet1
ip ospf 1 area 0.0.0.0
interface Ethernet2
ip ospf 1 area 0.0.0.0 - B. router ospf 1 vrf CCNP
network 10.0.0.0 0.0.255.255 area 0 - C. router ospf 1 vrf CCNP
interface Ethernet1
ip ospf 1 area 0.0.0.0
interface Ethernet2
ip ospf 1 area 0.0.0.0 - D. router ospf 1 vrf CCNP
network 10.1.1.1 0.0.0.0 area 0
network 10.2.2.2 0.0.0.0 area 0
正解：D
質問 # 33
Refer to the exhibit.
In which circumstance does the BGP neighbor remain in the idle condition?
- A. if a prefix list is applied on the inbound direction
- B. if prefixes reach the maximum limit
- C. if prefixes exceed the maximum limit
- D. if prefixes are not received from the BGP peer
正解：C
質問 # 34 
Refer to the exhibit. A network engineer troubleshooting a packet drop problem for the host 172.16.100.5 notices that only one link is used and installed on the routing table, which saturates the bandwidth. Which action must the engineer take to resolve the high bandwidth utilization problem and share the traffic toward this host between the two available links?
- A. Change the EIGRP delay metric to meet the feasibility condition.
- B. Set the eigrp variance equal to 4 to install a second route with a metric not larger than 4 times of the best metric.
- C. Disable the eigrp split horizon loop protection mechanism.
- D. Set the eigrp variance equal to 3 to install a second route with a metric not larger than 3 times of the best metric.
正解：A
質問 # 35
Refer to the exhibit.
A network administrator is discovering a Cisco Catalyst 9300 and a Cisco WLC 3504 in Cisco DNA Center.
The Catalyst 9300 is added successfully However the WLC is showing [ error "uncontactable" when the administrator tries to add it in Cisco DNA Center. Which action discovers WLC in Cisco DNA Center successfully?
- A. Add the WLC 3504 under the hierarchy of the Catalyst 9300 connected devices.
- B. Copy the .pern file from the Cisco DNA Center on the USB and upload it to the WLC 3504.
- C. Copy the .cert file from the Cisco DNA Center on the USB and upload it to the WLC 3504.
- D. Delete the WLC 3504 from Cisco DNA Center and add it to Cisco DNA Center again.
正解：B
解説：
Explanation
https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/109597-csr-chained-ce
質問 # 36
......
Cisco 300-410（Implementing Cisco Enterprise Advanced Routing and Services）認定試験は、エンタープライズネットワークにおける高度なルーティング技術とサービスの実装に関する候補者の知識とスキルを検証するために設計されています。この認定試験は、複雑なエンタープライズネットワークインフラストラクチャを設計、実装、トラブルシューティングする責任があるネットワークプロフェッショナルを対象としています。合格した候補者は、BGP、OSPF、EIGRP、およびIS-ISなどの高度なルーティングサービスを設定し、トラブルシューティングすることができ、セキュリティ、QoS、および自動化ソリューションを実装することができます。
300-410問題集、あなたを合格させる認証試験：https://jp.fast2test.com/300-410-premium-file.html
まもなくセール終了！リアル300-410のPDF解答を使おう：https://drive.google.com/open?id=1r22EN5ItOwvQtswIdaeGaoEszCrpFCtL