[2024年04月] 学習材料には有効な500-220効率的問題集！
最新の500-220テストエンジンPDF無料問題集保証！
Cisco 500-220試験は、クラウド管理ネットワーク、セキュリティ、ワイヤレス、スイッチング、およびSD-WANなどのCisco Merakiソリューションに関連するさまざまなトピックをカバーしています。この試験は、Cisco Merakiプラットフォームとその関連技術について深い理解を持つ専門家を対象としています。候補者は、実際の現場環境でCisco Merakiソリューションを実装および管理する実践的な経験を持っていることが期待されています。
質問 # 14
When wireless SSIDs are configured in Dashboard, which setting on the Access Control page affects the ability of a 2.4 GHz only client device from associating to the WLAN for the first time?
- A. Bridge mode
- B. Content filtering
- C. Dual band operating with Band Steering
- D. 802.11r
正解：C
解説：
Explanation
When band steering is enabled on an SSID, APs will stop advertising that SSID in 2.4GHz beacons. Since
2.4GHz-only clients that rely on a passive scan will not "see" that SSID in beacons, they might not be able to join this SSID unless they do an active scan or have been pre-configured with the SSID name and security settings (for example, a pre-shared key).
https://documentation.meraki.com/MR/Radio_Settings/Band_Steering
質問 # 15
Which Meraki Dashboard menu section is accessed to enable Sentry enrollment on an SSID?
- A. Wireless > Configure > Access Control
- B. Wireless > Configure > SSIDs
- C. Wireless > Configure > Firewall & Traffic Shaping
- D. Wireless > Configure > Splash page
正解：A
解説：
Explanation
SM Sentry enrollment can be enabled on any MR network via the Splash page section of the Wireless > Configure > Access control page.
https://documentation.meraki.com/MR/MR_Splash_Page/Systems_Manager_Sentry_Enrollment
質問 # 16
The WAN connection of a Cisco Meraki MX security appliance is congested, and the MX appliance is buffering the traffic from LAN ports going to the WAN ports. High, normal, and low priority queue buffers are all full. Which proportion of the normal traffic is forwarded compared to the other queues?
- A. 4/10 packets
- B. 2/7 packets
- C. 5/15 packets
- D. 2/10 packets
正解：B
解説：
Explanation
https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/SD-WAN_and_Traffic_Shaping
質問 # 17
Refer to the exhibit.
Assuming this MX has established a full tunnel with its VPN peer, how will the MX route the WebEx traffic?
- A. WebEx traffic will prefer WAN 2 as long as it meets the thresholds in the "Conf" performance class.
- B. WebEx traffic will prefer WAN 1 as it is the primary uplink.
- C. WebEx traffic will prefer WAN 2 as long as it is up.
- D. WebEx traffic will be load-balanced between both active WAN links.
正解：B
質問 # 18
Which type of authentication protocol is used when using OSPF on an MX appliance?
- A. MD5
- B. SHA-1
- C. certificate
- D. plaintext
正解：A
質問 # 19
Which two Systems Manager Live tools are available only for Apple Macs and Windows PCs and cannot be used on iOS or Android mobile devices? (Choose two.)
- A. Selective wipe
- B. OS updates
- C. Remote Desktop
- D. Send notification
- E. Screenshot
正解：A、C
質問 # 20
Which type of authentication protocol is used when using OSPF on an MX appliance?
- A. MD5
- B. SHA-1
- C. certificate
- D. plaintext
正解：A
解説：
Reference:
Using_OSPF_to_Advertise_Remote_VPN_Subnets
質問 # 21
What happens to an unsupervised iOS device when the "Meraki management" profile is removed?
- A. The "Meraki management" profile cannot be removed.
- B. The "Meraki management" profile is removed. All configuration profiles that Systems Manager pushed remain.
- C. The "Meraki management" profile is removed and then pushed automatically by Systems Manager.
- D. The "Meraki management" profile is removed. All configuration profiles that Systems Manager pushed are also removed.
正解：D
質問 # 22
Which three verbs of request are available in the Cisco Meraki API? (Choose three.)
- A. PATCH
- B. POST
- C. ADD
- D. SET
- E. PUT
- F. GET
正解：B、E、F
解説：
Reference:
Cisco_Meraki_Dashboard_API
質問 # 23
Refer to the exhibit.
What are two outcomes reflected in the Web App Health application? (Choose two.)
- A. Network #2 could not load Google because of a local client misconfiguration.
- B. Network #2 had better application performance than Network #1.
- C. Users on both networks may be experiencing issues when attempting to reach Google.
- D. Network #1 could not load Google because of a remote server issue.
- E. Neither network recorded any server-side performance issues.
正解：D、E
質問 # 24
Refer to the exhibit.
Which design recommendation should be considered?
- A. A 50-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 2-hop maximum.
- B. A 25-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 2-hop maximum.
- C. A 50-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 1-hop maximum.
- D. A 25-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 1-hop maximum.
正解：D
質問 # 25
A Cisco Meraki MV camera is monitoring an office and its field of vision currently captures work desks and employee computer screens. However, recording employee computer screens is prohibited by local regulation.
Which feature in Dashboard can be used to preserve the current position of the camera while also meeting regulation requirements?
- A. zone exclusion
- B. restricted mode
- C. area or interest
- D. privacy window
- E. sensor crop
正解：B
質問 # 26
What is a feature of distributed Layer 3 roaming?
- A. All wireless client traffic can be split-tunneled.
- B. An MX Security Appliance is not required as a concentrator.
- C. An MX Security Appliance is required as a concentrator.
- D. All wireless client traffic is tunneled.
正解：B
解説：
Explanation
https://documentation.meraki.com/Architectures_and_Best_Practices/Cisco_Meraki_Best_Practice_Design/Best This is a feature of distributed Layer 3 roaming, which maintains layer 3 connections for end devices as they roam across layer 3 boundaries without a concentrator1. The first access point that a device connects to will become the anchor access point1.
質問 # 27
Drag and drop the steps from the left into the sequence on the right to manage device control, according to Cisco Meraki best practice.
正解：
解説：
質問 # 28
Refer to the exhibit.
Which design recommendation should be considered?
- A. A 25-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 1-hop maximum.
- B. A 50-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 2-hop maximum.
- C. A 25-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 2-hop maximum.
- D. A 50-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 1-hop maximum.
正解：D
解説：
Explanation
https://documentation.meraki.com/MR/Deployment_Guides/Mesh_Deployment_Guide There will be a throughput reduction (~50% reduction) with each "hop" in a mesh. It is recommended that a mesh network be designed for no more than one mesh hop from the gateway to client device.
質問 # 29
Where should a network admin navigate to investigate wireless mesh information between Meraki APs?
- A. Wireless > Monitor > Wireless Health
- B. Wireless > Monitor > Access Points > AP > RF
- C. Wireless > Monitor > RF Spectrum
- D. Wireless > Configure > Radio Settings
正解：B
解説：
Explanation
See Monitoring Mesh section Mesh monitoring tools are located at the bottom of every AP detail page, which can be accessed by navigating to Wireless > Monitor > Access Points, then clicking on an Access Point.
https://documentation.meraki.com/MR/Wi-Fi_Basics_and_Best_Practices/Wireless_Mesh_Networking
質問 # 30
Refer to the exhibit.
Which condition or conditions will cause the "All Databases & cloud services" SD-WAN traffic to be routed via a VPN2 tunnel on WAN2?
- A. WAN1 tunnel latency is 20 ms or less, irrespective of WAN2 tunnel performance.
- B. WAN1 tunnel latency is 20 ms or more, and WAN2 tunnel meets the configured performance criteria.
- C. WAN1 tunnel latency is 20 ms or less, and WAN2 tunnel meets the configured performance criteria.
- D. WAN1 tunnel latency is 20 ms or more, irrespective of WAN2 tunnel performance.
正解：B
解説：
Explanation
This is because the SD-WAN policy for "All Databases & cloud services" has the following settings:
Uplink selection policy: Prefer WAN1, Fail over if down
Traffic filters: Custom performance classes
Custom performance classes: Database
Database performance criteria: Maximum latency 200 ms, Maximum jitter 20 ms, Maximum loss 1% This means that the SD-WAN traffic will be routed via WAN1 by default, unless WAN1 is down or fails to meet the database performance criteria. In that case, the traffic will be routed via WAN2, if WAN2 meets the database performance criteria. Therefore, the condition that will cause the traffic to be routed via WAN2 is when WAN1 tunnel latency is 20 ms or more (which exceeds the maximum jitter of 20 ms), and WAN2 tunnel meets the configured performance criteria (maximum latency 200 ms, maximum jitter 20 ms, maximum loss
1%).
質問 # 31
Which two features and functions are supported when using an MX appliance in Passthrough mode? (Choose two.)
- A. secondary uplinks
- B. site-to-site VPN
- C. intrusion prevention
- D. DHCP
- E. high availability
正解：B、C
解説：
Reference:
Passthrough_Mode_on_the_MX_Security_Appliance_and_Z-series_Teleworker_Gateway
質問 # 32
Refer to the exhibit.
What are the Loss and Average Latency statistics based on?
- A. responses that the MX appliance receives on the connectivity-testing hostnames on the Insight > Web App Health page
- B. responses that the MX appliance receives on the connectivity-testing IP addresses on the Help > Firewall info page
- C. responses that the MX appliance receives on the connectivity-testing IP address that is configured on the Security & SD-WAN > SD-WAN & Traffic Shaping page
- D. responses that the MX appliance receives on the connectivity-testing IP addresses on the Security & SD- WAN > Firewall page
正解：C
解説：
Explanation
Quote from referred documentation-Link: Loss and latency will be determined over the configured IP address under Security and SD-WAN > SD-WAN and Traffic Shaping > Uplink Statistics. If no IP is configured, these values will be measured against 8.8.8.8 by default. On the WAN Health page, all the configured IP address statistics can be reviewed by changing the destination under the "Ping Destination" column.
https://documentation.meraki.com/MI/MI_WAN_Health#:~:text=Current%20loss%20and%20latency%20statist
質問 # 33
Which configuration step is necessary when automatic updating is required of iOS apps provisioned through Systems Manager that are found in the App Store?
- A. Create a security policy that enables automatic updates.
- B. Create a profile with automatic update enabled and apply it to iOS devices.
- C. Configure automatic updating of iOS devices in the Meraki installed profile.
- D. No configuration step is necessary; automatic updating is the default behavior.
正解：D
解説：
Explanation
By default, iOS apps provisioned through Systems Manager that are found in the App Store will self-update if automatic updates has been turned on in the Settings. For custom iOS apps, or to manually push down updates, check the following steps.
https://documentation.meraki.com/SM/Apps_and_Software/Updating_Managed_iOS_Apps
質問 # 34
A Cisco Meraki MV camera is monitoring an office and its field of vision currently captures work desks and employee computer screens. However, recording employee computer screens is prohibited by local regulation.
Which feature in Dashboard can be used to preserve the current position of the camera while also meeting regulation requirements?
- A. zone exclusion
- B. area or interest
- C. privacy window
- D. restricted mode
- E. sensor crop
正解：C
解説：
Explanation
https://documentation.meraki.com/MV/Initial_Configuration/Privacy_Windows
質問 # 35
Refer to the exhibit.
What does the MX Security Appliance send to determine whether VPN traffic exceeds the configured latency threshold in the VoIP custom performance class?
- A. 1000-byte TCP probes every second, through VPN tunnels that are established over the primary WAN link.
- B. 1000-byte TCP probes every second, through VPN tunnels that are established over every WAN link.
- C. 100-byte UDP probes every second, through VPN tunnels that are established over the primary WAN link.
- D. 100-byte UDP probes every second, through VPN tunnels that are established over every WAN link.
正解：B
質問 # 36
......
Cisco 500-220試験は、Cisco Merakiソリューションの展開におけるエンジニアの知識とスキルをテストする認定試験です。この試験は、候補者がリアルワールドシナリオでCisco Merakiソリューションを設計、展開、トラブルシューティングする能力をテストすることを目的としています。また、Cisco Merakiソリューションの展開におけるベストプラクティスの実装能力も評価することを意図しています。
Cisco 500-220試験は、エンジニアリングCisco Meraki Solutionsの知識とスキルを検証したい専門家向けに設計されています。 Cisco Merakiは、ネットワークインフラストラクチャ、セキュリティ、および管理にハードウェアおよびソフトウェアソリューションを提供するクラウド管理IT企業です。認定試験では、候補者のMerakiアーキテクチャ、構成、実装、およびトラブルシューティングに関する知識のテストに焦点を当てています。
500-220問題集最新の練習テストと74独特な解答：https://jp.fast2test.com/500-220-premium-file.html
最新Cisco Meraki Solutions Specialist 500-220実際の無料試験解答：https://drive.google.com/open?id=1M0lwagUXCr3rHAadUpKoGb7Zr6rZIgK8