[Q32-Q53] テスト資料NSK101テストエンジン試験問題はここにある[2025年01月]

テスト資料NSK101テストエンジン試験問題はここにある[2025年01月]

合格突破受験者シミュレーションされたNSK101試験PDF問題を試そう

質問 # 32
Click the Exhibit button.

Referring to the exhibit, what are two recommended steps to be set on the perimeter device to monitor IPsec tunnels to a Netskope data plane? (Choose two.)

• A. Send HTTP requests to the Netskope location's Probe IP.
• B. Send ICMP requests to the Netskope location's proxy IPs.
• C. Enable IKE Dead Peer Detection (DPD) for each tunnel.
• D. Send ICMP requests to the Netskope location's Probe IP

正解：C、D

解説：
To monitor IPsec tunnels to a Netskope data plane, it is essential to ensure the stability and responsiveness of the tunnels. The recommended steps involve enabling monitoring mechanisms that detect and respond to tunnel failures. Here's a detailed explanation of the two recommended steps:
Enable IKE Dead Peer Detection (DPD) for each tunnel:
Implementation: Configure DPD in the IPsec settings of the perimeter device. This ensures that if the Netskope data plane is unreachable, the tunnel is automatically terminated and re-negotiated.
Send ICMP requests to the Netskope location's Probe IP:
Implementation: Set up regular ICMP requests (ping) from the perimeter device to the Netskope Probe IPs. This allows for continuous monitoring of the tunnel's health and immediate detection of connectivity issues.
Reference:
REST API v2 Overview - Netskope Knowledge Portal
Using the REST API v2 dataexport Iterator Endpoints - Netskope Knowledge Portal Using the REST API v2 UCI Impact Endpoints - Netskope Knowledge Portal

質問 # 33
You are adding a new tenant administrator in the Admins page. Which additional security measure would you be able to enable for only this new account?

• A. Add the administrator to the Administration Audit Log.
• B. Set the password expiration.
• C. Activate SSO authentication using an external identity provider.
• D. Activate MFA to log in to the Netskope management console.

正解：D

解説：
When adding a new tenant administrator in the Admins page, you can enhance the security for the new account by enabling Multi-Factor Authentication (MFA). MFA adds an extra layer of security by requiring the administrator to provide a second form of verification in addition to the password, thus protecting against unauthorized access.
References:
* Netskope documentation on user and admin account management, including the configuration and benefits of enabling MFA.
* Security best practices guides from Netskope, emphasizing the importance of MFA for enhanced account security.

質問 # 34
Click the Exhibit button.

A user has the Netskope Client enabled with the correct steering configuration applied. The exhibit shows an inline policy that has a predefined webmail category blocked. However the user is still able to access Yahoo mail.
Which statement is correct in this scenario?

• A. The user's AD group must be added to the policy.
• B. The webmail category does not include Yahoo mail when using an explicit proxy
• C. The user is not steered using an explicit proxy.
• D. The user is not part of the correct AD group or OU.

正解：B

解説：
The given exhibit shows an inline policy blocking the predefined webmail category via an explicit proxy. However, the user can still access Yahoo Mail, indicating that Yahoo Mail is not included in the webmail category when using an explicit proxy.
Policy Configuration:
The policy is set to block access to the webmail category through an explicit proxy.
The action for this policy is 'Block'.
Understanding the Webmail Category:
Netskope's predefined categories may not always cover all services under a category, especially when it comes to specific configurations like explicit proxy.
The webmail category in the policy might not have included Yahoo Mail when using explicit proxy configurations.
Checking the Category Definitions:
It is important to verify what URLs or services are included under the "webmail" category in the Netskope administration console.
Administrators can check the category definitions and manually add Yahoo Mail if it's not included by default.
Reference:
REST API v2 Overview - Netskope Knowledge Portal
Using the REST API v2 dataexport Iterator Endpoints - Netskope Knowledge Portal Using the REST API v2 UCI Impact Endpoints - Netskope Knowledge Portal netskopesdk * PyPI Netskope Rest APIv2(OAS 3.1) - Postman Collection

質問 # 35
There is a DLP violation on a file in your sanctioned Google Drive instance. The file is in a deleted state. You need to locate information pertaining to this DLP violation using Netskope. In this scenario, which statement is correct?

• A. You must create a forensic profile so that an incident is created.
• B. DLP incidents for a file are not visible when the file is deleted.
• C. You can find DLP violations under Forensic profiles.
• D. You can find DLP violations under the Incidents dashboard.

正解：D

解説：
To locate information pertaining to a DLP violation on a file in your sanctioned Google Drive instance, you can use the Incidents dashboard in Netskope. The Incidents dashboard provides a comprehensive view of all the incidents that have occurred in your cloud environment, such as DLP violations, malware infections, anomalous activities, etc. You can filter the incidents by various criteria, such as app name, incident type, severity, user name, etc. You can also drill down into each incident to see more details, such as file name, file path, file owner, file size, file type, etc. The Incidents dashboard can show DLP violations for files that are in a deleted state, as long as they are still recoverable from the trash bin of the app. If the file is permanently deleted from the app, then the incident will not be visible in the dashboard. Reference: Netskope Incidents Dashboard

質問 # 36
You want to take into account some recent adjustments to CCI scoring that were made in your Netskope tenant.
In this scenario, which two CCI attributes in the Ul would be used in a Real-time Protection policy? (Choose two.)

• A. GDPR Readiness
• B. CCL Level
• C. App Tag
• D. Domains

正解：B、C

解説：
When adjusting Cloud Confidence Index (CCI) scoring in your Netskope tenant, you can use the following two CCI attributes in a Real-time Protection policy:
* App Tag:
* App Tags are used to categorize and tag applications based on their functionality, risk level, or compliance requirements. By using App Tags in Real-time Protection policies, you can enforce security measures and monitor activities based on the specific tags assigned to applications.
* CCL Level:
* CCL (Cloud Confidence Level) is a score assigned to cloud applications based on their risk profile and compliance with security standards. By incorporating CCL Level into your Real-time Protection policies, you can ensure that actions are taken based on the risk level of the applications, such as blocking or monitoring high-risk applications.
References:
* Netskope Knowledge Portal: Cloud Confidence Index
* Netskope Real-time Protection Policies

質問 # 37
Which two technologies form a part of Netskope's Threat Protection module? (Choose two.)

• A. DLP
• B. heuristics
• C. sandbox
• D. log parser

正解：B、C

解説：
To protect your users from malicious scripts that may be downloaded from websites, you need to use technologies that can detect and prevent malware, ransomware, phishing, and other advanced threats in web traffic. Two technologies that form a part of Netskope's Threat Protection module, which is a feature in the Netskope platform that provides these capabilities, are sandbox and heuristics. Sandbox is a technology that allows Netskope to analyze suspicious files or URLs in a virtual environment isolated from the rest of the network. It simulates the execution of the files or URLs and observes their behavior and impact on the system.
It then generates a verdict based on the analysis and blocks any malicious files or URLs from reaching your users or devices. Heuristics is a technology that allows Netskope to identify unknown or emerging threats based on their characteristics or patterns, rather than relying on predefined signatures or rules. It uses machine learning and artificial intelligence to analyze various attributes of files or URLs, such as file type, size, entropy, metadata, code structure, etc., and assigns a risk score based on the analysis. It then blocks any files or URLs that exceed a certain risk threshold from reaching your users or devices. A log parser or DLP are not technologies that form a part of Netskope's Threat Protection module, as they are more related to discovering cloud applications or protecting sensitive data. References: [Netskope Threat Protection], Netskope Security Cloud Operation & Administration (NSCO&A) - Classroom Course, Module 9: Threat Protection.

質問 # 38
Which two controls are covered by Netskope's security platform? (Choose two.)

• A. EDR
• B. ZTNA
• C. CASB
• D. VPN

正解：B、C

解説：
Netskope's security platform covers two controls: ZTNA and CASB. ZTNA stands for Zero Trust Network Access, which is a solution that provides secure and granular access to private applications without exposing them to the internet or requiring VPNs. CASB stands for Cloud Access Security Broker, which is a solution that provides visibility and control over cloud services and web traffic, as well as data and threat protection for cloud users and devices. Reference: Netskope PlatformNetskope ZTNANetskope CASB

質問 # 39
Which three statements about Netskope Private Access Publishers are correct? (Choose three.)

• A. Publishers can be deployed as hardware or software appliances to provide access to applications across disparate locations.
• B. Publishers can be deployed in both private data centers and public cloud providers to provide access to applications across disparate locations.
• C. Publishers can run on Windows or Linux servers.
• D. Publishers only make outbound connections to the Netskope Security Cloud which reduces the amount of public exposure.
• E. Publisher deployment can be automated in public cloud environments using Netskope's REST API.

正解：B、C、D

解説：
The following statements about Netskope Private Access Publishers are correct:
Publishers can run on Windows or Linux servers:
Publishers are versatile and can be installed on both Windows and Linux operating systems.
Publishers can be deployed in both private data centers and public cloud providers to provide access to applications across disparate locations:
This flexibility allows organizations to use Publishers to connect applications hosted in various environments, ensuring seamless access across locations.
Publishers only make outbound connections to the Netskope Security Cloud which reduces the amount of public exposure:
By making only outbound connections, Publishers minimize the attack surface, enhancing security by reducing public exposure.
Reference:
Netskope Private Access Deployment Guide
Netskope REST API v2 Overview

質問 # 40
You determine that a business application uses non-standard HTTPS ports. You want to steer all HTTPS traffic for this application and have visibility and control over user activities.
Which action will allow you to accomplish this task?

• A. Configure Non-standard ports in the Steering Configuration.
• B. Select All Traffic in the Steering Configuration.
• C. Create a steering exception for the application's domain and ports.
• D. Define a Private Agg for the application's domain and ports.

正解：A

解説：
* Identify Non-standard HTTPS Ports:
Determine the specific non-standard HTTPS ports used by the business application.
* Create a Steering Exception:
Navigate to the Netskope admin console.
Go to the steering configuration section and create a new steering exception.
Specify the domain of the business application and include the non-standard HTTPS ports.
This exception will ensure that traffic to this application is steered correctly for inspection and control.
* Configure Non-standard Ports in the Steering Configuration:
Go to the steering configuration settings.
Add the identified non-standard HTTPS ports to ensure that all traffic using these ports is captured and inspected.
This ensures comprehensive visibility and control over the user activities on the application.
* Reference:
For more details on steering configurations and managing exceptions, refer to the Netskope documentation on steering traffic and configuring non-standard ports.

質問 # 41
Which three security controls are offered by the Netskope Cloud platform? (Choose three.)

• A. identity lifecycle management
• B. cloud security posture management
• C. data loss prevention for SMTP
• D. endpoint anti-malware
• E. threat protection

正解：B、C、E

解説：
Three security controls that are offered by the Netskope Cloud platform are: C. cloud security posture management, E. threat protection, and B. data loss prevention for SMTP.
* Cloud security posture management is a service that provides continuous assessment and remediation of
* public cloud deployments for risks, threats, and compliance issues. Netskope CSPM leverages the APIs available from cloud service providers such as AWS, Azure, and GCP to scan the cloud infrastructure for misconfigurations, such as insecure permissions, open ports, unencrypted data, etc. Netskope CSPM also provides security posture policies,profiles, and rules that can be customized to match the security standards and best practices of the organization or industry.
* Threat protection is a capability to detect and block malware, ransomware, phishing, and other cyber threats that may compromise cloud data or users. Netskope threat protection uses advanced techniques such as machine learning, sandboxing, threat intelligence, and behavioral analysis to identify and prevent malicious activities in real time.Netskope threat protection also integrates with third-party solutions such as antivirus engines, firewalls, SIEMs, etc., to provide comprehensive defense across the cloud and web1.
* Data loss prevention for SMTP is a feature that allows you to protect sensitive data that is sent or received via email. Netskope DLP for SMTP can scan email messages and attachments for predefined or custom data patterns, such as credit card numbers, social security numbers, health records, etc., and apply appropriate actions, such as block, quarantine, encrypt, notify, etc., based on the DLP policies.Netskope DLP for SMTP can also support multiple email domains and routing rules for different groups of users2.

質問 # 42
You are creating a real-time policy for cloud applications.
In addition to users, groups, and organizational units, which two source criteria would support this scenario? (Choose two.)

• A. browser version
• B. protocol version
• C. device classification
• D. access method

正解：C、D

解説：
When creating a real-time policy for cloud applications, you can use access method and device classification as source criteria, in addition to users, groups, and organizational units. Access method refers to how the user accesses the cloud application, such as browser, sync client, mobile app, etc. Device classification refers to the type of device used by the user, such as managed or unmanaged, Windows or Mac, etc. These criteria can help you define granular policies based on different scenarios and risks. Reference: [Creating Real-Time Policies for Cloud Applications]

質問 # 43
A company is attempting to steer traffic to Netskope using GRE tunnels. They notice that after the initial configuration, users cannot access external websites from their browsers.
What are three probable causes for this issue? (Choose three.)

• A. Netskope does not support GRE tunnels.
• B. The route map was applied to the wrong router interface.
• C. The configured GRE peer in the Netskope platform is incorrect.
• D. The corporate firewall might be blocking GRE traffic.
• E. The pre-shared key for the GRE tunnel is incorrect.

正解：B、C、D

解説：
In this scenario, there are three probable causes for the issue of users not being able to access external websites from their browsers after attempting to steer traffic to Netskope using GRE tunnels. One cause is that the configured GRE peer in the Netskope platform is incorrect, which means that the Netskope POP that is supposed to receive the GRE traffic from the customer's network is not matching the IP address of the customer's router that is sending the GRE traffic. This will result in a failure to establish a GRE tunnel between the customer and Netskope. Another cause is that the corporate firewall might be blocking GRE traffic, which means that the firewall rules are not allowing the GRE protocol (IP protocol number 47) or the UDP port 4789 (for VXLAN encapsulation) to pass through. This will result in a failure to send or receive GRE packets between the customer and Netskope. A third cause is that the route map was applied to the wrong router interface, which means that the configuration that specifies which traffic should be steered to Netskope using GRE tunnels was not applied to the correct interface on the customer's router. This will result in a failure to steer the desired traffic to Netskope. The pre-shared key for the GRE tunnel is incorrect is not a probable cause for this issue, as GRE tunnels do not use pre-shared keys for authentication or encryption.
Netskope does support GRE tunnels, so this is not a cause for this issue either. References: [Netskope Secure Forwarder], Netskope Security Cloud Operation & Administration (NSCO&A) - Classroom Course, Module
3: Steering Configuration, Lesson 3: Secure Forwarder.

質問 # 44
What are two characteristics of Netskope's Private Access Solution? (Choose two.)

• A. It requires on-premises hardware.
• B. It provides protection for private applications.
• C. It provides access to private applications.
• D. It acts as a cloud-based firewall.

正解：B、C

解説：
Netskope's Private Access Solution is a service that allows users to securely access private applications without exposing them to the internet or using VPNs. It provides protection for private applications by encrypting the traffic, enforcing granular policies, and preventing data exfiltration. It also provides access to private applications by creating a secure tunnel between the user's device and the application's server, regardless of their location or network. It does not act as a cloud-based firewall, as it does not filter or block traffic based on ports or protocols. It does not require on-premises hardware, as it is a cloud-native solution that leverages Netskope's global network of points of presence (POPs). References: [Netskope Private Access].

質問 # 45
Why would you want to define an App Instance?

• A. to differentiate between an enterprise Google Drive instance vs. a personal Google Drive instance
• B. to differentiate between an enterprise Google Drive instance vs. an enterprise Box instance
• C. to create an API Data Protection Policy for a personal Box instance
• D. to enable the instance_id attribute in the advanced search field when using query mode

正解：A

解説：
An App Instance is a feature in the Netskope platform that allows you to define and identify different instances of the same cloud application based on the domain name or URL. For example, you can define an App Instance for your enterprise Google Drive instance (such as drive.google.com/a/yourcompany.com) and another App Instance for your personal Google Drive instance (such as drive.google.com). This way, you can differentiate between them and apply different policies and actions based on the App Instance. You would want to define an App Instance to achieve this level of granularity and control over your cloud application activities. Creating an API Data Protection Policy for a personal Box instance, enabling the instance_id attribute in the advanced search field, or differentiating between an enterprise Google Drive instance vs. an enterprise Box instance are not valid reasons to define an App Instance, as they are either unrelated or irrelevant to the App Instance feature. References: Netskope Security Cloud Operation & Administration (NSCO&A) - Classroom Course, Module 5: Real-Time Policies, Lesson 4: App Instances.

質問 # 46
Which two statements are correct about DLP Incidents in the Netskope platform? (Choose two.)

• A. An incident can be associated to one or more DLP rules.
• B. An incident can have one or more DLP violations.
• C. An incident can be associated to one or more DLP policies.
• D. An incident can be assigned to one or more administrators.

正解：A、B

解説：
Two statements that are correct about DLP Incidents in the Netskope platform are: An incident can have one or more DLP violations and an incident can be associated to one or more DLP rules. A DLP violation occurs when a file or object matches a DLP rule used in a DLP profile. A DLP rule defines the criteria for detecting sensitive data, such as keywords, regular expressions, fingerprints, machine learning classifiers, etc. A DLP profile is a collection of DLP rules that can be applied to a policy. An incident is a record of a file or object that triggered a DLP policy violation. An incident can have multiple violations if the file or object matches multiple DLP rules from different profiles. An incident can also be associated to multiple DLP rules if the file or object matches more than one rule from the same profile. References: About DLPDLP Profiles

質問 # 47
The Netskope deployment for your organization is deployed in CASB-only mode. You want to view dropbox.com traffic but do not see it when using SkopeIT.
In this scenario, what are two reasons for this problem? (Choose two.)

• A. The Dropbox domains are configured to steer to the Netskope tenant.
• B. The Dropbox Web application is certificate pinned and cannot be steered to the Netskope tenant.
• C. The Dropbox desktop application is certificate pinned and cannot be steered to the Netskope tenant.
• D. The Dropbox domains have not been configured to steer to the Netskope tenant.

正解：B、D

解説：
In a CASB-only deployment of Netskope, there could be several reasons why Dropbox.com traffic is not visible in SkopeIT:
* Certificate Pinning:
* The Dropbox Web application might be using certificate pinning, which means it only accepts specific certificates for its connections. This can prevent the traffic from being steered to the Netskope tenant because the proxy's certificate might not match the pinned certificate.
* Configuration of Dropbox Domains:
* If the Dropbox domains are not properly configured to be steered to the Netskope tenant, then the traffic will bypass the Netskope inspection and will not be visible in SkopeIT. Ensuring that the domains are configured correctly is essential for the traffic to be captured and analyzed by Netskope.
References:
* "Certificate pinning prevents the interception of traffic by requiring that the presented certificate matches a known good certificate. This can interfere with traffic steering in CASB deployments.".
* "Proper configuration of application domains is necessary to ensure traffic is steered to the Netskope tenant for inspection and visibility.".

質問 # 48
What are two uses for deploying a Netskope Virtual Appliance? (Choose two.)

• A. as a Secure Forwarder to steer traffic
• B. as a local reverse-proxy to secure a SaaS application
• C. as a log parser to discover in-use cloud applications
• D. as an endpoint for Netskope Private Access (NPA)

正解：A、D

解説：
A Netskope Virtual Appliance is a software-based appliance that can be deployed on-premises or in the cloud to provide various functions and features for the Netskope Security Cloud platform. One use for deploying a Netskope Virtual Appliance is as an endpoint for Netskope Private Access (NPA), which is a service that allows users to securely access private applications without exposing them to the internet or using VPNs.
Another use for deploying a Netskope Virtual Appliance is as a Secure Forwarder to steer traffic from on-premises devices or networks to the Netskope platform for inspection and policy enforcement. Using a Netskope Virtual Appliance as a local reverse-proxy to secure a SaaS application or as a log parser to discover in-use cloud applications are not valid uses, as these functions are performed by other components of the Netskope Security Cloud platform, such as the Cloud Access Security Broker (CASB) or the Cloud XD engine. References: Netskope Security Cloud Operation & Administration (NSCO&A) - Classroom Course, Module 2: Architecture Overview; [Netskope Private Access]; [Netskope Secure Forwarder].

質問 # 49
All users are going through Netskope's Next Gen SWG. Your CISO requests a monthly report of all users who are accessing cloud applications with a "Low" or a "Poor" CCL, where the activity is either "Edit" or "Upload".
Using the Advanced Analytics interface, which two statements describe which actions must be performed in this scenario? (Choose two.)

• A. Schedule a report with a monthly recurrence to be sent by SMS with the attached PDF document at the end of each month.
• B. Schedule a report with a monthly recurrence to be sent by e-mail with the attached PDF document at the end of each month.
• C. Create a report using the Data Collection "Page Events", filtering on the activities "Edit" and "Upload" for cloud apps with CCL values of "Low" or "Poor".
• D. Create a report using the Data Collection "Application Events" filtering on the activities "Edit" and "Upload" for cloud apps with CCL values of "Low" or "Poor".

正解：B、C

解説：
* Create the Report in Advanced Analytics:
Data Collection:
Use the "Page Events" data collection, which captures detailed user activities on web pages, including edits and uploads.
Filters:
Apply filters to include only the activities "Edit" and "Upload".
Add another filter for the Cloud Confidence Level (CCL) to include only those with "Low" or "Poor" ratings.
This ensures the report focuses on the specified user activities within cloud applications that have lower security ratings.
Steps:
Navigate to Advanced Analytics > Reports.
Create a new report and select "Page Events" as the data collection source.
Apply the necessary filters for activities and CCL values.
* Schedule the Report:
Monthly Recurrence:
Set the report to run on a monthly schedule to ensure regular updates.
Configure the report to be sent via email with a PDF attachment.
Steps:
In the report scheduling options, set the recurrence to monthly.
Specify the email recipients, ensuring the CISO receives the report.
Select PDF as the report format.
* Reference:
For more details on creating and scheduling reports, refer to the Netskope documentation on Advanced Analytics and report generation.

質問 # 50
Digital Experience Management (DEM) allows an administrator to monitor which two areas? (Choose two.)

• A. Information on triggered policies
• B. Client steering data
• C. User activities
• D. Bandwidth consumption

正解：B、D

解説：
Digital Experience Management (DEM) in Netskope allows administrators to monitor the following areas:
* Bandwidth consumption: DEM provides insights into how much bandwidth is being used by different applications and services, helping administrators to optimize network performance and ensure efficient use of resources.
* Client steering data: DEM collects data on how traffic is being steered through the Netskope infrastructure, including details about routing decisions, performance metrics, and user experiences. This helps administrators understand the impact of their steering policies and make adjustments to improve performance.
User activities (option A) and information on triggered policies (option C) are more directly related to other features such as activity logs and policy enforcement dashboards rather than DEM.
References:
* Netskope documentation on Digital Experience Management.
* Guides on monitoring and optimizing network performance using DEM.

質問 # 51
A Netskope administrator wants to create a policy to quarantine files based on sensitive content.
In this scenario, which variable must be included in the policy to achieve this goal?

• A. DLP Profile
• B. Organizational Unit
• C. Cloud Confidence Index level
• D. Threat Protection Profile

正解：A

解説：
To create a policy to quarantine files based on sensitive content in Netskope, you need to include the DLP Profile variable. Here's a detailed explanation of the steps involved:
* Access Netskope Admin Console: First, log in to your Netskope admin console.
* Navigate to Policies: Go to the Policies section where you can create and manage different types of policies.
* Create a New Policy: Click on the option to create a new policy. Select the type of policy you want to create. In this case, it will be a Data Loss Prevention (DLP) policy.
* Define Policy Criteria: Define the criteria for your policy. This includes specifying the conditions under which files should be quarantined. You will need to include sensitive content detection as part of the criteria.
* Include DLP Profile: The most crucial step is to include a DLP Profile in your policy. The DLP Profile will define the sensitive content that the policy will monitor for. Netskope provides various predefined DLP profiles that you can use, or you can create custom DLP profiles based on your organization's needs.
* Set Action to Quarantine: Specify the action to be taken when the policy criteria are met. In this case, you want to quarantine the files. Select the "Quarantine" action from the available options.
* Save and Apply Policy: Once you have configured the policy with the DLP profile and action, save the policy and apply it to the relevant users, groups, or organizational units.
References:
* Netskope Knowledge Portal: Using DLP Profiles and Policies.

質問 # 52
What correctly defines the Zero Trust security model?

• A. strong authentication
• B. least privilege access
• C. multi-layered security
• D. double encryption

正解：B

解説：
The term that correctly defines the Zero Trust security model is least privilege access. The Zero Trust security model is a modern security strategy based on the principle: never trust, always verify. Instead of assuming everything behind the corporate firewall is safe, the Zero Trust model assumes breach and verifies each request as though it originates from an open network. One of the core principles of the Zero Trust model is to use least privilege access, which means granting users or systems only the minimum level of access they need to perform their tasks, and only for a limited time. This helps reduce the attack surface and minimize the impact of a potential breach. References: Zero Trust Security - microsoft.comWhat is Zero Trust Security?
Principles of the Zero Trust Model

質問 # 53
......

正真正銘で最適なNSK101オンライン練習試験資料：https://jp.fast2test.com/NSK101-premium-file.html