JN0-663問題一発合格させる問題集はJNCIP-SP認定で！ [Q12-Q33]

JN0-663問題一発合格させる問題集はJNCIP-SP認定で！

JN0-663練習テストPDF試験材料

質問 12
Exhibit.

You have the LDP signaled VPLS topology as shown in the exhibit CE-B at Site-2 is multihomed to both PE-2 and PE-3 In this scenario where would you configure loop prevention?

A. PE-2
B. CE-B
C. PE-3
D. PE-1

正解: D

質問 13
Exhibit.

Two CE devices (CE-1 and CE-2) belong to the same customer and connect into a single PE device (PE-1) However, the CE devices cannot communicate with each other You want to allow the CE devices to communicate with each other Referring to the exhibit, which action would solve the problem?

A. Configure both routing instances with the vrf-table-label statement
B. Configure both routing instances with the set routing-options autonomous-system loops 3 statement
C. Configure both routing instances with the as-override statement within the BGP protocol
D. Configure both routing instances with the set routing-opt ions auto-export-statement

正解: D

質問 14
Click the Exhibit button.

A network administrator is investigating why traffic from R2 is not being forwarded to R1 Referring to the show isis database command output shown in the exhibit, what is causing this problem on the network?

A. R1 and R2 are in different IS-IS areas.
B. The preferred interface between R1 and R2 is experiencing errors
C. R1 is configured to drop all incoming traffic.
D. R2 is ignoring specific LSPs from R1 in its SPF calculations.

正解: D

質問 15
Exhibit:

Referring to the exhibit, you are asked to summarize all routes in the 10.10.0 0/22 address range ensuring that a single summary route is present in area 49.0002 while the IS-IS internal contributing routes are restricted to area 49.0001. All other routes must not be affected.
Which two operations would have to be performed on R2 to accomplish this task? (Choose two.)

A. Include the to level 2 match criteria when referencing the summary route.
B. Create and apply a policy with two terms; one to accept the summary route and one to reject the contributing routes.
C. Include the from level 1 match criteria when referencing the summary route.
D. Create and apply a policy with a single term to accept only the summary route.

正解: A,B

質問 16
Exhibit:

Referring to the exhibit, which statement is true?

A. The route is learned from three different neighbors.
B. This is a multipath route.
C. The route is learned from only one neighbor.
D. This is a multihop route.

正解: D

質問 17
Exhibit.

Referring to the exhibit, which two statements are correct for a route advertised by R1 towards R4? (Choose two )

A. The AS path is set to 150 by R2
B. The BGP next hop is set to 14.1 1.1 byR2
C. The AS path is set to null by R2
D. The BGP next hop is set to 192.168.2 2 by R2

正解: B

質問 18
Exhibit:

Referring to the exhibit, which two statements about route reflectors are correct? (Choose two.)

A. RR1 advertises routes learned from Client1 to RR2 with itself as the next hop.
B. RR2 advertises routes learned from Client3 to EBGP2 with itself as the next hop.
C. RR2 adds its cluster ID when advertising routes from CHent4 to Client3.
D. RR1 and RR2 need the same cluster ID to exchange routes learned from their clients.

正解: B,C

質問 19
Exhibit:

Referring to the exhibit, which two statements are true? (Choose two.)

A. An AS loop will not exist between CE-1 and CE-2 and the BGP routes will be shared.
B. The CE-1 and CE-2 routes will have the same route distinguisher, which will not stop the BGP routes from being shared.
C. An AS loop will exist between CE-1 and CE-2 and the BGP routes will not be shared.
D. The CE-1 and CE-2 routes will have the same route distinguisher, which will stop the BGP routes from being shared.

正解: B,C

質問 20
Exhibit:

A network administrator is concerned about the number of LSAs that they are observing on the network.
What will reduce Type 7 LSAs advertised from R2 to the non-backbone routers shown in the exhibit?

A. Configure no-summaries under protocols ospf3 on R2.
B. Configure no-summaries under area 0.0.0.2 on R2.
C. Configure no-naaa-abr under protocols ospf3 on R2.
D. Configure nssa under area 0.0.0.2 on R2.

正解: C

質問 21
Exhibit:

You notice an inconsistency between the routing table and the OSPF database, as shown in the exhibit.
What are two reasons for this behavior? (Choose two.)

A. An OSPF import policy is being applied to the route.
B. The LSA is a Type 5 LSA.
C. An OSPF export policy is being applied to the route.
D. The LSA is a Type 4 LSA.

正解: A,B

質問 22
Exhibit:

Traffic is being sent from R2 to R3. The link between R2 and R3 fails.
Referring to the exhibit, which statement is correct?

A. Manual intervention is required for traffic to be rerouted.
B. Traffic will automatically reroute using the shortest path, which is R2 to R1 to R3.
C. Traffic will automatically reroute distributed between all available paths.
D. Traffic will automatically reroute using R2 to R4 to R1 to R3.

正解: D

質問 23
Exhibit:

You must configure an OSPF virtual link to facilitate communication between Area 0 and Area 20.
Referring to the exhibit, which two addresses should you use as the neighbor IDs of the virtual link endpoints?
(Choose two.)

A. The address that is associated with R2's xe-1/2/0 interface.
B. The address that is associated with R4's router ID.
C. The address that is associated with R2's router ID.
D. The address that is associated with R4's xe-0/0/1 interface.

正解: B,C

質問 24
Exhibit:

All adjacencies have been formed, no extra options have been configured, and no policies have been written.
Referring to the exhibit, which two statements are correct? (Choose two.)

A. R1 can reach R5.
B. R1 cannot reach R5
C. R2 will create a default route and send it as a TLV to R1
D. R1 will create its own default route that points to R2

正解: A,C

質問 25
Exhibit.

R2 has IS-IS adjacencies with R3 and R4 You want to ensure that R2 has both a level 1 and level 2 adjacency to both R3 and R4 but R2 only has one adjacency with R4.
Referring to the exhibit, which configuration change will solve this issue?

A. Change the IS-IS area on R4 to match R2
B. Remove the level 1 disable configuration from R2
C. Change the IS-IS area on R2 to match R4.
D. Remove the level 1 disable configuration from R4

正解: A

質問 26
Exhibit:

Referring to the exhibit, the local BGP router is receiving IPv4 routes from the BGP neighbor, but it is not receiving L3 VPN routes from the BGP neighbor.
Which two actions should you take to solve this problem? (Choose two.)

A. Configure the family inet unicast statement on the local BGP router.
B. Configure the family inet unicast statement on the BGP neighbor
C. Configure the family inet-vpn unicast statement on the BGP neighbor.
D. Configure the family inet-vpn unicast statement on the local BGP router.

正解: C,D

質問 27
Exhibit:

Referring to the exhibit, which path would traffic passing through R1 take to get.

A. R1 -> R3 -> R5 -> R6
B. R1 -> R2 -> R4 -> R6
C. R1 -> R2 -> R3 -> R6
D. R1 -> R3 -> R4 -> R6

正解: A

質問 28
Exhibit:

Referring to the exhibit, which two statements about route reflectors are correct? (Choose two.)

A. RR1 advertises routes learned from Client1 to RR2 with itself as the next hop.
B. RR2 advertises routes learned from Client3 to EBGP2 with itself as the next hop.
C. RR2 adds its cluster ID when advertising routes from CHent4 to Client3.
D. RR1 and RR2 need the same cluster ID to exchange routes learned from their clients.

正解: B,C

質問 29
Exhibit:

All adjacencies have been formed, no extra options have been configured, and no policies have been written.
Referring to the exhibit, which two statements are correct? (Choose two.)

A. R1 can reach R5.
B. R1 cannot reach R5
C. R2 will create a default route and send it as a TLV to R1
D. R1 will create its own default route that points to R2

正解: A,C

質問 30
Which two statements regarding Ethernet segments (ES) are correct? (Choose two.)

A. The Type-4 EVPN route will be used to elect the designated forwarder for the ES.
B. The Type-3 EVPN route will be used for the aliasing function to load-balance to the ES.
C. The Type-1 EVPN route will indicate if the ES is all-active or single-active.
D. The Type-2 EVPN route will indicate if there is a designated forwarder on the ES.

正解: A,C

質問 31
Exhibit:

CE-1, CE-2, and CE-3 are part of a single VPLS VPN An Ethernet frame has just arrived at PE-3 from CE-3.
It has a source MAC address of CE-3 and a destination MAC address of CE-1. You want to know what PE-3 does with the Ethernet frame.
Referring to the exhibit, which statement is correct?

A. It forwards the packet to PE-1 only.
B. It drops the packet because the destination MAC address is not in PE-3's MAC table.
C. It drops the packet because the destination MAC address is not for PE-3.
D. It forwards the packet to PE-1 and PE-2.

正解: D

質問 32
What is the purpose of the duster-list attribute within a BGP route reflector group?