[2025年02月]更新のNS0-093認定実際の問題を提供します
更新されたのはNS0-093問題集PDFでNS0-093リアル有効なブレーン問題集には63問があります！
Network Appliance NS0-093認定試験は、NetAppストレージシステムを扱うIT専門家にとって必要不可欠な認定試験です。認定試験は、NetAppハードウェアコンポーネントのインストール、構成、およびトラブルシューティングに関する候補者の知識とスキルをテストします。認定試験には、キャリアアップ、サポートリソースへのアクセス、および収益増加などの多くの利点があります。
Network Appliance NS0-093認定試験は、NetAppストレージシステムを扱うハードウェアサポートエンジニアにとって重要なステップです。この試験に合格し、NetApp認定ハードウェアサポートエンジニアになることで、候補者はこの分野での専門知識を証明し、IT業界で多くのキャリアチャンスを得ることができます。適切なトレーニングと準備を行うことで、候補者はこの権威ある認定を取得し、NetAppストレージシステムに依存するすべての組織にとって貴重なアセットになることができます。
ネットワークアプライアンスNS0-093試験は、ハードウェアサポートエンジニアリングの分野でキャリアを求めている専門家向けに設計されています。この試験は、NetAppハードウェア製品をサポートするために必要なスキルと知識を検証することを目的としています。この試験は、NetAppハードウェアシステムのインストール、構成、トラブルシューティングの経験がある個人を対象としています。
質問 # 21
Where is a kernel core file stored on a FAS9000 system that is running ONTAP 9.12.1 software?
- A. on the root aggregate
- B. on the partner root aggregate
- C. on the boot device
- D. on the mailbox disk
正解：A
解説：
On a FAS9000 system running ONTAP 9.12.1, the kernel core file is stored on the root aggregate. This is the default location where ONTAP writes kernel core files for system-level failures.
* The root aggregate is the aggregate that contains the root volume for a given node in the cluster. This aggregate is used for critical system files and logs, including kernel core files.
* When a kernel panic or other critical failure occurs, the core dump is written to the root aggregate for later analysis by NetApp Support.
Key Details:
* A. on the partner root aggregate: The partner root aggregate is not used for storing core files unless explicitly configured (which is not the default behavior).
* C. on the mailbox disk: The mailbox disk is used for cluster quorum and configuration information, not for storing core files.
* D. on the boot device: The boot device contains ONTAP software and boot files but does not store kernel core dumps.
* "ONTAP System Administration Guide" specifies that core files are stored on the root aggregate.
* NetApp's "Troubleshooting and Diagnostics Guide" confirms the default behavior for kernel core file storage.
Why Other Options Are Incorrect:References:
質問 # 22
Following an unexpected takeover, the taken-over node is waiting for giveback. The administrator plans to perform a giveback with the option -cfo-only true.
What happens if this option is used?
- A. Only the data aggregates are sent back.
- B. Only SVM root volumes are sent back
- C. Only the root aggregate is given back.
- D. Only a simulation of the giveback is performed.
正解：A
解説：
Purpose of the -cfo-only true Option:
* This option is used during the giveback process in a NetApp cluster to control which aggregates are returned to the original node.
* By specifying -cfo-only true, only the data aggregates are given back to the original node, while the root aggregate remains with the takeover node.
Use Case:
* This command is helpful when you want to test the aggregate giveback functionality or if the root aggregate requires further investigation or maintenance before returning it to the original node.
NetApp Reference Documentation:
* The "ONTAP High-Availability Configuration Guide" and "Cluster Failover Management Guide" detail the behavior of the -cfo-only option during giveback scenarios.
質問 # 23
What happens when the command diskcopy is run from nodeshell?
- A. It performs a low-level copy of the disk to another disk.
- B. It pre-fails a drive in an aggregate and copies it to a spare.
- C. It copies the disk content to a specified volume.
- D. It triggers a RAID reconstruction of that disk.
正解：A
解説：
Purpose of the diskcopy Command:
* The diskcopy command is used in the ONTAP nodeshell environment to perform a low-level sector-by- sector copy of data from one disk to another. This is typically used during data recovery or diagnostics.
How It Works:
* The command copies all sectors from the source disk to the destination disk without any regard for file system or metadata structures.
* It is commonly used when replicating the exact state of a failing disk to a spare for further analysis or recovery.
Key Notes:
* The destination disk must be of the same or larger capacity than the source disk.
* The operation is typically disruptive and not suitable for production use.
NetApp Reference Documentation:
* Found in the "ONTAP Command Line Manual" for nodeshell utilities. The diskcopy process is highlighted as a low-level disk cloning operation.
質問 # 24
You have upgraded your cluster from ONTAP 9.5 software to ONTAP 9.7 software. After the upgrade, you notice that the upgrade causes issues. You decide to revert to ONTAP 9.5 software.
Which revert step is allowed?
- A. Revert directly from ONTAP 9.7 software to ONTAP 9.5 software.
- B. Revert to ONTAP 9.5 software with the netboot procedure.
- C. Revert from ONTAP 9.7 software to ONTAP 9.5 software by using the boot backup procedure.
- D. Revert from ONTAP 9.7 software to ONTAP 8.6 software and then to ONTAP 9.5 software.
正解：B
解説：
Reverting to a Previous ONTAP Version:
* Reverting ONTAP software requires specific procedures and is only supported if the ONTAP version being reverted to is compatible with the current cluster configuration.
Why the Netboot Procedure Is Used:
* The netboot process loads the desired ONTAP version directly into memory from a network location and reinitializes the system.
* This method is used when a full software revert is required and is often necessary for downgrades to a version that cannot be directly reverted to from the running ONTAP version.
Key Notes:
* A direct revert is not supported from ONTAP 9.7 to ONTAP 9.5 using standard methods due to system metadata changes.
* Always verify compatibility using the "ONTAP Software Version Interoperability Matrix".
NetApp Reference Documentation:
* Refer to the "ONTAP Revert/Downgrade Guide" for specific instructions on using the netboot procedure.
質問 # 25
Which LOADER prompt command ensures that POST is done on boot?
- A. boot_ontap
- B. bye
- C. setenv POST=true
- D. boot_diag
正解：C
解説：
To ensure that POST (Power-On Self-Test) runs on boot, the setenv POST=true command is used at the LOADER prompt. This command enables the system to perform POST diagnostics before proceeding with the boot process.
* POST Purpose: POST checks system hardware components (such as memory, disk, and controllers) for faults before loading the ONTAP kernel.
* How to Use:
* At the LOADER prompt, type:
Key Details:arduino
Copy code
setenv POST=true
* Save the configuration and reboot the system.
* B. bye:
* This command restarts the system but does not ensure that POST runs on boot.
* C. boot_diag:
* This command boots the system into diagnostic mode but is not directly related to enabling POST on boot.
* D. boot_ontap:
* This command boots ONTAP but skips POST if it is not explicitly enabled.
Why Other Options Are Incorrect:
* NetApp "ONTAP System Boot and Recovery Guide" describes setenv POST=true for enabling POST diagnostics.
References:
質問 # 26
Which two NetApp tools should be used when troubleshooting the root cause of an unexpected controller reboot? (Choose two.)
- A. ONTAP Mediator
- B. ONTAP CLI
- C. Active IQ Config Advisor
- D. Active IQ Digital Advisor
- E. Active IQ Unified Manager
正解：B、E
解説：
To troubleshoot the root cause of an unexpected controller reboot, the following tools are commonly used:
* What it does:Provides monitoring and performance data for the ONTAP cluster, including historical event logs that may help identify the root cause of a reboot.
1. Active IQ Unified Manager
* What it does:The CLI allows you to gather logs and status information directly from the affected node.
Commands like event log show and system core are essential for identifying the reason behind the reboot.
2. ONTAP CLI
* B. Active IQ Digital Advisor:
* This tool focuses on predictive analytics and proactive recommendations, not troubleshooting unexpected reboots.
* D. ONTAP Mediator:
* This tool is used for managing MetroCluster configurations, not for troubleshooting reboots.
* E. Active IQ Config Advisor:
* This tool checks for configuration best practices but does not provide detailed logs or reboot diagnostics.
Why Other Options Are Incorrect:
* NetApp "ONTAP System Management Guide" emphasizes the use of Unified Manager and CLI for troubleshooting system issues.
References:
質問 # 27
You have identified that the file named quarterly_25.docx is inconsistent.
Which nodeshell command reports whether there are Snapshot copies available?
- A. "priv set diag; file check -v <voiname> -i <field>"
- B. "priv set advanced; file check -f quarterly_25.docx"
- C. "priv set advanced; aggr wafliron start -f quarterly_25.docx"
- D. "priv set diag; snap list -f quarterly_25.docx"
正解：A
質問 # 28
After a panic, the customer asks you to explain the error "watchdog timeout." Which explanation would be appropriate?
- A. A service that monitors network activity and protects data.
A watchdog induces system panic to protect data if malicious activity is detected. - B. An optional software that monitors system performance.
An overloaded system fails to reset the watchdog and watchdog induces a system panic. - C. A service that detects and recovers from computer malfunctions.
A hardware or software error prevents update of watchdog and it induces a system panic. - D. An optional component included with Active IQ Unified Manager.
It notifies a user if watchdog fails to reach the storage system within a certain period.
正解：C
解説：
What Is a Watchdog Timeout?
* The watchdog is a software or hardware mechanism that monitors the system's health and ensures it is operating correctly.
* If the system fails to respond or update the watchdog timer within the specified time, the watchdog triggers a system panic to avoid further corruption or damage.
Cause of Watchdog Timeout:
* This usually occurs due to:
* A hardware failure (e.g., CPU or memory issue).
* A software bug causing a system hang or crash.
* The panic ensures the system stops operation to preserve data integrity and aid in troubleshooting.
NetApp Reference Documentation:
* "ONTAP Troubleshooting Guide" and "Core Dump Analysis Guide" provide details on interpreting watchdog timeouts and recommended actions.
質問 # 29
Which two steps are required to replace a drawer in a DS460c shelf? (Choose two.)
- A. Power off the shelf.
- B. Disconnect the cable chains from the chassis.
- C. Shut down both nodes.
- D. Evacuate all drives in the drawer.
正解：B、D
質問 # 30
In which two sections of AutoSupport can you find information to analyze the following panic? (Choose two.) Panic_Message: PCI Error NMI from device(s):ErrSrcID(CorrSrc(0xf00),UCorrSrc(0x18)), RPT(0,3,0):
Qlogic FC 16G adapter in slot 1 on Controller
- A. PCI-HIERARCHY.XML
- B. SSRAM-LOG
- C. ALL-COREDUMP.XML
- D. HA-RASTRACE.TGZ
正解：B、D
解説：
To analyze the provided panic error, the two sections of AutoSupport that are essential for investigation are:
* What it is:HA-RASTRACE.TGZ contains HA (High Availability) system trace logs. It records hardware diagnostics, error traces, and the HA system's response to hardware events. These logs are critical when analyzing hardware-related panics, including those caused by PCI errors.
* Why it's relevant to the panic:In the given panic message, the NMI (Non-Maskable Interrupt) error originates from a Qlogic FC 16G adapter. HA-RASTRACE.TGZ will provide detailed diagnostics, including the error reporting from the HA interconnect and other hardware diagnostics. Specifically, it may include information about how the system detected the PCI fault and any actions taken to protect the system state.
* How to analyze:
* Extract the HA-RASTRACE.TGZ file from the AutoSupport bundle.
* Review hardware-related trace messages for entries associated with the PCI bus or the Qlogic FC adapter.
* Look for specific error codes or keywords like PCI Error, NMI, or Qlogic.
* References:
* NetApp's "AutoSupport Logs and Diagnostics Guide" highlights HA-RASTRACE.TGZ as a primary resource for debugging hardware faults.
* The "Panic Troubleshooting Guide" for ONTAP systems specifies HA-RASTRACE as a key source for identifying NMI-related errors.
1. HA-RASTRACE.TGZ
* What it is:SSRAM-LOG records low-level hardware error details, including PCI device register states and uncorrectable memory errors. It is particularly useful for analyzing errors originating in peripheral hardware like network or storage adapters connected via PCI.
* Why it's relevant to the panic:The panic message explicitly references a PCI Error NMI caused by a Qlogic FC adapter. SSRAM-LOG captures detailed state information for PCI devices, which can help identify whether the fault originated in the adapter hardware, the PCI bus, or another related component.
* How to analyze:
* Extract the SSRAM-LOG from the AutoSupport bundle.
* Search for PCI-related errors, including the specific error source IDs (e.g., ErrSrcID(CorrSrc (0xf00),UCorrSrc(0x18))).
* Review the log entries to confirm the root cause of the NMI.
* References:
* The "Hardware Diagnostics and Troubleshooting Guide for ONTAP" lists SSRAM-LOG as a key file for debugging PCI errors.
* NetApp's documentation on PCI diagnostics emphasizes the use of SSRAM-LOG for validating hardware-level faults.
2. SSRAM-LOG
質問 # 31
Which two commands from the Service Processor can provide information about installed field replaceable units (FRUs)? (Choose two.)
- A. system sensors show
- B. system fru show
- C. system power status
- D. system fru list
正解：B、D
解説：
To view information about installed Field Replaceable Units (FRUs) using the Service Processor, the following commands are used:
* What it does:Displays a list of all installed FRUs, such as disks, power supplies, and fans.
* Example Usage:
1. system fru listsystem fru list
* What it does:Provides detailed information about specific FRUs, including serial numbers, statuses, and hardware details.
2. system fru showsystem fru show
* C. system sensors show:
* This command displays sensor data (e.g., temperature, voltage) but does not list FRUs.
* D. system power status:
* This command shows power supply status but does not provide FRU details.
Why Other Options Are Incorrect:
* "Service Processor Commands Guide" from NetApp provides a comprehensive overview of system fru list and system fru show.
References:
質問 # 32
Which two of the following methods are valid ways to access a node which is not booting? (Choose two.)
- A. serial console
- B. Service Processor
- C. cluster management port
- D. node management port
正解：A、B
解説：
If a node is not booting, the following methods can be used to access the system for troubleshooting:
* What it does:The SP provides out-of-band management access to the node, even if the node is not booting.
* How to use:
* Connect to the SP using SSH or a direct console connection.
* Use SP commands to gather logs or perform diagnostics.
1. Service Processor (SP)
* What it does:The serial console provides direct access to the node's bootloader or maintenance mode.
* How to use:
* Connect to the serial port using a terminal emulator.
* Use console commands to interact with the system.
2. Serial Console
* A. node management port:
* The node management interface is only accessible if the node is booted and ONTAP is running.
* B. cluster management port:
* The cluster management interface requires the cluster to be operational, which is not possible if the node is not booting.
Why Other Options Are Incorrect:
* NetApp "Service Processor and Serial Console Guide" provides instructions for accessing a non- booting node.
References:
質問 # 33
On a NetApp FAS9000 system, which two field replaceable units (FRUs) are supported for replacement without takeover? (Choose two.)
- A. I/O module
- B. caching module
- C. NVRAM module
- D. DCPM module
正解：A、C
解説：
FRUs on FAS9000 Supporting Replacement Without Takeover:
* A (I/O Module): I/O modules can be replaced hot (without takeover) to maintain system uptime during hardware servicing.
* D (NVRAM Module): NVRAM modules on FAS9000 can also be replaced without a node takeover, ensuring data integrity during replacement.
Why Other Options Are Incorrect:
* B (DCPM Module): The DCPM (Data Center Power Management) module is not hot-swappable and requires a node takeover.
* C (Caching Module): The caching module is integrated and typically requires a node takeover or power-down for replacement.
NetApp Reference Documentation:
* Refer to the "NetApp FAS9000 Hardware Service Guide" for supported FRU replacement procedures and operational constraints.
質問 # 34
In preparation for an upgrade to ONTAP 9.6P8 software, you have uploaded the ONTAP image
96P8_q_nodar_image.tgz onto your local web server with address 192.168.10.10.
Which is correct command syntax to download this image to the cluster image repository?
- A. ClusterA::> storage firmware download -node local -package-url
http://192.168.10.10/96P8_q_nodar_image.tgz - B. ClusterA::> cluster image package get -url
http://192.168.10.10/96P8_q_nodar_image.tgz - C. SP ClusterA-01> cluster image package get -url
http://192.168.10.10/96P8_q_nodar_image.tgz - D. ClusterA::> cluster image package get -url
http://netapp.com/ontap9/downloads/96P8_q_nodar_image.tgz
正解：B
解説：
Command Syntax for Downloading ONTAP Image:
* The cluster image package get command is used to download the ONTAP image from a specified URL to the cluster's image repository.
* The syntax requires the -url parameter followed by the full URL of the image file.
Why Option C Is Correct:
* This command syntax directly downloads the image from the local web server at http://192.168.10.10/ to the ONTAP cluster repository.
* Other options either refer to incorrect commands or unsupported URLs.
NetApp Reference Documentation:
* The "ONTAP Software Upgrade Guide" provides the exact command and steps for downloading ONTAP images via HTTP or FTP.
質問 # 35
While performing a health check on a cluster, you notice the following entries in the cluster event log:
Referring to the exhibit, which of the following actions do you take?
- A. Sanitize the disk.
- B. Review the current firmware and known issues.
- C. Use diskcopy to copy the disk to a working spare.
- D. Reseat the disk.
正解：B
解説：
Analyzing the Error in the Event Log:
* The log entry indicates a medium error on a disk, suggesting an unrecoverable read issue.
* While the RAID subsystem attempts to reconstruct unreadable data, this error might indicate a firmware issue or a compatibility problem with the disk.
Why Reviewing Firmware and Known Issues Is Important:
* Medium errors can sometimes result from outdated or incompatible firmware.
* By reviewing firmware release notes and known issues for the disk model (NETAPP X381_HLBRE10TSDB in this case), you can identify if this is a known issue and resolve it by updating the firmware.
Other Options:
* Sanitize the disk (Option A): Not relevant here, as sanitization is used for secure data erasure.
* Reseat the disk (Option B): Useful for addressing hardware seating issues, but not the first step here.
* Diskcopy to a spare (Option D): This is a last-resort recovery step and not the primary action.
NetApp Reference Documentation:
* "ONTAP Disk Management Guide" and "Disk Firmware Release Notes" detail how to handle medium errors and update firmware.
質問 # 36
What are the two steps to unfail a disk in maintenance mode? (Choose two.)
- A. Use the "disk unfair command.
- B. Use the disk remove command.
- C. Reseat the disk.
- D. Remove it from the Failed Disk Registry.
正解：A、D
解説：
Steps to Unfail a Disk in Maintenance Mode:
* When a disk is marked as "failed," it is added to the Failed Disk Registry and marked as unusable by the system. Unfailing a disk involves removing it from this registry and resetting its state.
Step 1: Remove the Disk from the Failed Disk Registry
* Use the command: registry remove <disk> to delete the disk from the Failed Disk Registry. This clears its "failed" status.
Step 2: Use the Disk Unfail Command
* Execute the disk unfail <disk> command to reset the disk status and make it available for use.
Key Notes:
* After unfailing, the disk will be treated as a spare and must be reassigned or re-added to an aggregate.
* If the disk remains failed after these steps, physical hardware issues may need to be addressed.
NetApp Reference Documentation:
* The "ONTAP Maintenance Mode Guide" and "Disk Management Guide" provide detailed instructions for handling failed disks and using the disk unfail command.
質問 # 37
How do you set environment variables to factory settings?
- A. wipeconfig
- B. unsetenv all
- C. set-defaults
- D. setenv factory
正解：C
解説：
To reset environment variables to factory settings, the set-defaults command is used. This command clears all customizations and restores the environment variables to their default values.
* Command Syntax:At the LOADER prompt, type:
Key Details:arduino
Copy code
set-defaults
* Effect:This command resets all environment variables (e.g., boot arguments, diagnostic settings) to their original factory defaults.
* B. unsetenv all:
* This command clears all environment variables, but it does not restore them to factory defaults.
* C. setenv factory:
* This is not a valid command in NetApp systems.
* D. wipeconfig:
* This command is used to clear configuration and logs but does not reset environment variables.
Why Other Options Are Incorrect:
* NetApp "System Configuration Guide" confirms the use of set-defaults for restoring environment variables to factory settings.
References:
質問 # 38
Which type of AutoSupport message would you expect to see triggered automatically when ONTAP software detects a NetApp WAFL inconsistency on an aggregate?
- A. MEDIUM ERROR DURING RECONSTRUCTION
- B. WAFL INCONSISTENT BLOCK
- C. WAFL INCONSISTENT USER DATA BLOCK
- D. CHECKSUM ERROR
正解：B
解説：
When ONTAP detects a WAFL inconsistency in an aggregate, it automatically generates an AutoSupport message with the description WAFL INCONSISTENT BLOCK.
* WAFL INCONSISTENT BLOCK:
* This error indicates that WAFL metadata or user data blocks have been found to be inconsistent.
* ONTAP triggers an automatic AutoSupport message to notify administrators and NetApp Support.
Key Details:
* A. MEDIUM ERROR DURING RECONSTRUCTION:
* This error occurs during disk reconstruction, not due to WAFL inconsistencies.
* B. CHECKSUM ERROR:
* A checksum error indicates a disk-level data integrity issue, not a WAFL inconsistency.
* C. WAFL INCONSISTENT USER DATA BLOCK:
* While related, this is not the specific AutoSupport message triggered by ONTAP.
Why Other Options Are Incorrect:
* NetApp "ONTAP WAFL Troubleshooting Guide" describes AutoSupport messages related to WAFL inconsistencies.
References:
質問 # 39
You are reviewing the output of disk show and one of the disks is reporting a container type of "unknown".
What is causing this status?
- A. The disk is failed.
- B. The disk does not have an owner.
- C. The disk is not owned by a member of the high-availability (HA) pair.
- D. The disk is in the maintenance center.
正解：B
解説：
Understanding "Container Type: Unknown" in Disk Show Output:
* The "unknown" container type typically indicates that the disk is not properly configured or recognized by ONTAP.
* This status often occurs when a disk does not have an owner assigned.
Root Cause:
* For a disk to be used in an ONTAP system, it must be owned by a member of the high-availability (HA) pair.
* If no ownership is assigned, the disk will not be initialized, resulting in an "unknown" container type.
Steps to Resolve:
* Use the disk assign command to manually assign ownership of the disk.
* Example: storage disk assign -disk <disk_name> -owner <node_name>
NetApp Reference Documentation:
* "ONTAP Disk Management Guide" explicitly states that unowned disks report "unknown" container type until they are assigned to a node.
* This is further detailed in the "ONTAP Troubleshooting Guide" under disk configuration issues.
質問 # 40
Which two factors can increase the chances of experiencing a NetApp WAFL inconsistency on an aggregate?
(Choose two.)
- A. constantly running at high load
- B. ignoring NetApp Active IQ health risks
- C. using outdated disk firmware
- D. upgrading frequently
正解：B、C
解説：
* A. Ignoring NetApp Active IQ health risks
* Explanation:NetApp Active IQ provides proactive monitoring and alerts for system health risks, including risks related to WAFL inconsistencies. Ignoring these alerts can lead to unresolved issues such as metadata corruption, hardware failures, or system misconfigurations, increasing the chances of WAFL inconsistencies.
* Examples of Active IQ Risks:
* Disk health warnings.
* High write latency or metadata bottlenecks.
* Aggregates running out of space.
* C. Using outdated disk firmware
* Explanation:Outdated disk firmware can cause performance issues, drive failures, or incorrect handling of I/O operations, potentially leading to WAFL inconsistencies. Disk firmware updates often include fixes for critical issues that improve reliability and prevent data corruption.
* Importance:Keeping firmware updated ensures compatibility with ONTAP and minimizes risks of disk-level errors that can propagate to WAFL.
Why the Other Options Are Incorrect:
* B. Constantly running at high load:
* Running at high load can impact performance but does not directly cause WAFL inconsistencies.
WAFL is designed to handle high I/O loads efficiently.
* D. Upgrading frequently:
* Frequent upgrades, when performed correctly, do not increase the chances of WAFL inconsistencies. However, improperly executed upgrades or skipping recommended steps might introduce risks.
References:
* NetApp Knowledge Base: Articles on Active IQ health checks and disk firmware management.
* ONTAP System Administration Guide: Recommendations for preventing WAFL inconsistencies.
質問 # 41
In maintenance mode, which of the following commands shows disk ownership?
- A. aggr status
- B. sysconfig -v
- C. storage show disk -p
- D. disk show -v
正解：D
解説：
In maintenance mode, the command disk show -v provides detailed information about disk ownership. This includes the current owner, previous owner, and disk health status.
* Enter maintenance mode, and run:
How to Use:disk show -v
* The output will display ownership information for each disk, including its RAID group and current assignment.
* A. sysconfig -v:
* This command provides system configuration details but does not show disk ownership.
* C. aggr status:
* This command shows the status of aggregates, not individual disks or their ownership.
* D. storage show disk -p:
* This command is not valid in maintenance mode.
Why Other Options Are Incorrect:
* NetApp "Maintenance Mode Commands Guide" highlights disk show -v as the command to check disk ownership.
References:
質問 # 42
Which RAID type provides protection against three disk failures?
- A. RAID-TEC
- B. RAID DP
- C. RAID 5
- D. RAID 4
正解：A
解説：
RAID-TEC Overview:
* RAID-TEC (Triple Erasure Coding) is a NetApp RAID technology designed to protect against up to three simultaneous disk failures.
* It is ideal for systems with high-density disks or workloads requiring extreme fault tolerance.
Why RAID-TEC Is Correct:
* RAID-TEC uses triple-parity protection, which provides redundancy against three disk failures, making it more resilient than RAID-DP or RAID 5.
* RAID-DP only protects against two disk failures, while RAID 4 and RAID 5 protect against a single failure.
NetApp Reference Documentation:
* "NetApp RAID and Data Protection Guide" details the differences between RAID-DP and RAID-TEC, highlighting RAID-TEC's ability to tolerate three failures.
質問 # 43
......
あなたをお手軽にNS0-093試験合格させるし100%試験合格保証：https://jp.fast2test.com/NS0-093-premium-file.html