[2023年11月] 問題集簡単概要CRE試験問題Fast2test
CREトレーニング認証最新版をゲットASQ Certification
ASQ CRE 試験は、信頼性工学に関連する幅広いトピックをカバーしています。統計解析、確率論、信頼性モデリング、信頼性向上のための設計、予測メンテナンスなどが含まれます。この試験は、4 時間で完了しなければならない 150 問の多肢選択問題から構成されています。合格するためには、候補者は少なくとも 70% のスコアを取得して ASQ CRE 認定を受ける必要があります。
質問 # 34
Design review should be a process to ensure and/or develop more reliable design. Which of the following person(s), if any, should work with the designer during the design process?
Response:
- A. Management team.
- B. Designer only
- C. Design supervisor.
- D. Reliability engineer.
正解：D
質問 # 35
What is the factor of safety for the material?
Response:
- A. 0.75
- B. 1.50
- C. 1.33
- D. 0.66
正解：C
質問 # 36
A software sneak circuit is BEST described as which of the following?
Response:
- A. An invalid, executable path
- B. An error-handling routine
- C. An infinite loop
- D. Dead code
正解：A
質問 # 37
Software reliability planning includes all of the following EXCEPT
Response:
- A. Trade-offs of general purpose programs vs. commercially available programs.
- B. Selecting models for data analysis and prediction.
- C. Modeling acquisition of computer software systems.
- D. Trade-offs involving cost, schedule, and failure intensity of software products
正解：A
質問 # 38
The software test design method that involves seeding errors into a program is known is:
Response:
- A. Equivalent class partitioning.
- B. Fault insertion and error handling.
- C. Test cases.
- D. Customer defect reports.
正解：B
質問 # 39
In which of the following distribution is the standard deviation equal to the mean?
Response:
- A. Binomial.
- B. Poisson.
- C. Negative binomial.
- D. Exponential.
正解：C
質問 # 40
When a large number of components have been tested for a fixed time with no failure then:
Response:
- A. The Laplace rule of succession will apply.
- B. The failure rate is indeterminable.
- C. The failure rate is at least an individual test time.
- D. The failure rate is equivalent to the sum of the individual test times.
正解：B
質問 # 41
The influence of FMEA on reliability is maximized at which of the following stages of development?
Response:
- A. Operation.
- B. Design.
- C. Test.
- D. Prototype.
正解：B
質問 # 42
The equation below represents
Response:
- A. The limits for an X Bar control chart.
- B. The process capability adjusted for centering.
- C. The probability of meeting specification.
- D. The limits for a Range chart.
正解：B
質問 # 43
Which of the following is the BEST method of selecting parts of a new product?
Response:
- A. Drawing them from an approved parts list
- B. Performing incoming inspection.
- C. Using only those that have a high reliability.
- D. Using those that represent that latest technology.
正解：A
質問 # 44
Which of the following is a primary concern for a reliability engineer who uses publicly available sources for mechanical part-failure rates?
Response:
- A. Recognizing that the quantity of such data is unlimited.
- B. Finding appropriate data for each application.
- C. Meeting parts-count requirements
- D. Assuring that the data are in compliance with ISO standards.
正解：B
質問 # 45
Internal testing sources of component reliability data are:
Response:
- A. Warranty returns and Customer complaints.
- B. Prototype and Reliability growth.
- C. Government furnished data.
- D. Industry and Public data.
正解：B
質問 # 46
High cycle fatigue would MOST likely result in
Response:
- A. Constant failure.
- B. Wear out failure.
- C. Early failure.
- D. Mid-life failure.
正解：B
質問 # 47
When failed field item are returned for failure investigation, which of the following steps should be taken first?
Response:
- A. The physics of failure should be used to determine failure mechanism.
- B. The manufacturing process should be reviewed to ensure that it was followed during the production of the failed items.
- C. Each item should be investigated to classify and completely determine the failure mode
- D. Each item's predicted reliability should be compared with its actual reliability.
正解：C
質問 # 48
A primary purpose of burn-in testing of parts is to
Response:
- A. Ensure that parts operate at elevated temperatures.
- B. Eliminate substandard parts.
- C. Measure the temperature/stress distribution of parts.
- D. Ensure that parts are safe.
正解：B
質問 # 49
In a certain application, two identical transducers are used to measure the vacuum in a system. The system is considered to have failed if either of the vacuums read by the transducers varies from the standard by more than 10mm Hg.
Which of the following is the correct reliability logic block diagram for the transducer assembly?
Response:
- A. Option A
- B. Option B
- C. Option C
- D. Option D
正解：A
質問 # 50
The following fault tree diagram was developed by a team.
The probability are as follow:
A1 = 0.90 B1 = 0.90 C1 = 0.80
A2 = 0.80 B3 = 0.80 C2 = 0.70
A4 = 0.70
The likelihood that the system fault will occur is
Response:
- A. 0.3686
- B. 0.4977
- C. 0.3073
- D. 0.5034
正解：B
質問 # 51
Which of the following is NOT a degradation mechanism?
Response:
- A. Wear
- B. Crack
- C. Fatigue
- D. Derate
正解：D
質問 # 52
......
ASQ CRE認定プログラムは、航空宇宙、自動車、医薬品、電子など、さまざまな産業で働くプロフェッショナルに適しています。製品設計、テスト、および生産プロセスに関与する人々に特に有益です。このプログラムは、品質エンジニアリング分野のリーディングプロフェッショナル協会であるアメリカ品質協会（ASQ）によって開発されました。 ASQ CRE認定は、米国国防総省やNASAを含む、多くの組織でグローバルに認知されています。
認証トレーニングCRE試験問題集テストエンジン：https://jp.fast2test.com/CRE-premium-file.html
ASQ Certification CREリアル試験問題と解答無料最新になります：https://drive.google.com/open?id=1u5m4GqJyuOfUL1la0RNuAlGnWm4TWYIO