最新の[2023年06月07日]HP HPE2-W09試験練習テスト最高成績で最速合格をゲットせよ！
これを使えば必ず合格させる問題集でHP HPE2-W09
質問 # 62
You need to integrate Aruba Fabric Composer (AFC) with customer datacenter software. Is this integration possible?
Solution: Aruba Fabric Composer (AFC) with Nutanix Hypervisor (AHV)
- A. No
- B. Yes
正解：B
解説：
Aruba Fabric Composer (AFC) with Nutanix Hypervisor (AHV) integration is possible. AFC is a tool that provides automation and orchestration for managing data center networks composed of ArubaOS-CX switches. AFC can integrate with various data center software such as VMware vSphere, Nutanix AHV, Microsoft Hyper-V, etc. AFC can discover, monitor, and configure Nutanix AHV clusters and hosts using REST APIs1.
質問 # 63
Refer to the exhibits.
Is this how the switch-1 handles the traffic?
Solution: A broadcast arrives in VLAN 10 on Switch-1. Switch 1 forwards the frame on all interfaces assigned to VLAN 10, except the incoming interface. It encapsulates the broadcast with VXIAN and sends it to 192.168.1.3, out not 192.168.1.2.
- A. No
- B. Yes
正解：B
質問 # 64
Is this part of a valid strategy for load sharing traffic across the links in an Ethernet Ring Protection Switching (ERPS) ring?
Solution: Implement Virtual Switching Extension (VSX) on pairs of ERPS switches at the same site. Then combine multiple links between two data centers into VSX LAGs (M-LAGs).
- A. No
- B. Yes
正解：B
質問 # 65
You are configuring Ethernet Ring Protection Switching (ERPS) on an ArubaOS-CX switch. Is this a guideline for configuring timers?
Solution: The guard interval is set in units of seconds and is used to prevent frequent topology changes due to a link going up and down.
- A. No
- B. Yes
正解：A
解説：
The guard interval is set in units of seconds and is used to prevent frequent topology changes due to a link going up and down is not a guideline for configuring timers for Ethernet Ring Protection Switching (ERPS) on an ArubaOS-CX switch. The guard interval is set in units of milliseconds, not seconds, and it is used to prevent false ring failures due to short link outages or flapping1.
質問 # 66
You are using NetEdit to manage AruDaOS-CX switches. You want to deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address.
Is this what you should do?
Solution: Create two configuration plans, one with the standard config and one with the device-specific settings.
- A. No
- B. Yes
正解：A
解説：
Creating two configuration plans, one with the standard config and one with the device-specific settings, is not what you should do. NetEdit is a tool that allows you to manage and monitor multiple switches from a single interface1. It also provides a plan feature that lets you create containers to group devices and execute operations on them, such as deploying, committing, or rolling back device configuration or firmware1. However, you do not need to create two configuration plans for your scenario. You can create one configuration plan with the standard config and use variables to define the device-specific settings1. Variables are placeholders that can be replaced with different values for different devices1. This way, you can deploy a standard config with device-specific settings using one configuration plan1.
質問 # 67
An ArubaOS-CX is \ssmq DCBX on Interface 1/1/1. You enter this command:
show dcbx interface 1/1/1
Is this where you can see whether the connected converged network adapter (CNA) has accepted the application priorities advertised with DCBX?
Solution: in the Application Priority Map Local advertisement section
- A. No
- B. Yes
正解：B
解説：
The show dcbx interface command shows the current DCBx status and the configuration of PFC, ETS, and application priority applied on the interface and the status of the TLVs received from the peer1. The Application Priority Map section shows the protocol, port/type and priority for both local and remote advertisements. Therefore, this is where you can see whether the connected converged network adapter (CNA) has accepted the application priorities advertised with DCBX. Reference: https://www.arubanetworks.com/techdocs/AOS-CX/AOSCX-CLI-Bank/cli_8400/Content/Chp_DCBx/DCBx_cmds/sho-dcb-int.htm
質問 # 68
You are using NetEdit to manage AruDaOS-CX switches. You want to deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address.
Is this what you should do?
Solution: Inside a configuration plan, light-click any device-specific parameters and modify the parameter per-device.
- A. No
- B. Yes
正解：A
質問 # 69
Refer to the exhibits.
Is this how the switch handles the traffic?
Solution: A frame with destination MAC address, 00:50:56:00:00:03 arrives with a VLAN 10 tag on 1/1//1 on Switch-1. Switch-1 switches the frame out interface 1/1/2 without VXLAN.
- A. No
- B. Yes
正解：A
解説：
VXLAN is a tunneling protocol that encapsulates layer 2 traffic over an IP network using VXLAN Network Identifiers (VNIs) to identify different layer 2 segments. VXLAN Tunnel Endpoints (VTEPs) are devices that perform the encapsulation and decapsulation of VXLAN packets. According to the exhibit, Switch-1 and Switch-2 are VTEPs that use VNI 10010 to map VLAN 10 traffic. Therefore, when Switch-1 receives a frame with destination MAC address 00:50:56:00:00:03 and VLAN 10 tag on interface 1/1/1, it should encapsulate the frame with a VXLAN header that contains VNI 10010 and send it as a unicast packet to Switch-2's loopback address (10.1.1.2) over the IP network1. Switch-1 should not switch the frame out interface 1/1/2 without VXLAN, as this would violate the VNI mapping and cause layer 2 loops. Therefore, this is not how the switch handles the traffic. https://networklessons.com/cisco/ccnp-encor-350-401/introduction-to-virtual-extensible-lan-vxlan
質問 # 70
Is this a best practice when positioning ArubaOS-CX switches in data center networks?
Solution: Deploy Aruba CX 83xx switches as data center spine switches.
- A. No
- B. Yes
正解：B
質問 # 71
Is this a guideline for establishing a Virtual Switching Extension (VSX) Inter-Switch Link (ISL) between two ArubaOS-CX switches?
Solution: Use the same speed on every link In the ISL.
- A. No
- B. Yes
正解：B
解説：
The solution is correct because using the same speed on every link in the ISL is a guideline for establishing a VSX ISL between two ArubaOS-CX switches. Using the same speed on every link in the ISL ensures consistent performance and avoids potential issues with link aggregation. Therefore, using the same speed on every link in the ISL is a good practice for establishing a VSX ISL.
質問 # 72
Refer to the exhibit.
The company wants AtubaOS-CX switches to provide VXLAN services for several VMs and servers, as shown in the exhibit. Hypervisors will not run VXLAN for this solution. Is this part of a valid configuration to meet the requirements?
Solution: Attach VNIs 5010 and 5020 to interface 1/1/3 on Switch-2.
- A. No
- B. Yes
正解：B
質問 # 73
Your customer is using Nutanix AHV and they need a network orchestration tool to simplify network provisioning. Is this operation supported when Aruba Fabric Composer (AFC) is integrated with Nutanix?
Solution: Automated provisioning of LAGs Between AHV and VSX
- A. No
- B. Yes
正解：A
質問 # 74
Does this correctly describe how Network Analytics Engine (NAE) agents work?
Solution: Agents collect data every minute and send the data to a centralized SNMP server in SNMP traps.
- A. No
- B. Yes
正解：A
解説：
Agents do not collect data every minute and send the data to a centralized SNMP server in SNMP traps. NAE is a feature that provides network operators with distributed analytics for faster troubleshooting and resolution of network-impacting issues1. Agents are scripts that run on ArubaOS-CX switches and collect data from various sources, such as CLI commands, REST APIs, or syslog messages1. Agents can also define conditions and actions based on the collected data1. Agents do not send the data to a centralized SNMP server, but store it locally on the switch1. Agents can also send alerts to external systems, such as email servers or syslog servers, but not in SNMP traps1. The statement is false because it incorrectly describes how NAE agents work.
質問 # 75
Refer to the exhibits.
Is this how the switch-1 handles the traffic?
Solution: A broadcast arrives in VLAN 10 on Switch-1. Switch 1 forwards the frame on all interfaces assigned to VLAN10. except the incoming interface. It replicates the broadcast, encapsulates each broadcast with VXLAN. and sends the VXLAN traffic to 192.168.1.2 and 192.168.1.3.
- A. No
- B. Yes
正解：A
質問 # 76
Does this correctly describe Network Analytics Engine (NAE) limitations on ArubaOS-CX switches?
Solution: Different switches have different limitations for the number of NAE scripts, monitors, and agents supported.
- A. No
- B. Yes
正解：A
質問 # 77
You are using NetEdit to manage AruDaOS-CX switches. You want to deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address.
Is this what you should do?
Solution: omit the device-specific settings from the configuration plan and include them in command scripts instead.
- A. No
- B. Yes
正解：A
解説：
Omit the device-specific settings from the configuration plan and include them in command scripts instead is not what you should do if you want to use NetEdit to manage ArubaOS-CX switches and deploy a standard config to the switches, but need the config to include a few device-specific settings such as hostname and IP address. This approach would require you to create separate command scripts for each switch, which can be tedious and error-prone. A better approach would be to use an auto config plan that uses scripts to customize the configuration for each switch based on variables such as serial number, MAC address, or user-defined parameters1.
質問 # 78
......
正真正銘のベスト問題集資料を使おうHPE2-W09オンライン練習試験：https://jp.fast2test.com/HPE2-W09-premium-file.html